12:30 a.m.
Hi,
I am trying to install new libvirt version on Ubuntu 12.04 LTS. Now I downloaded libvirt
1.0.5 from libvirt.org/sources then I issued three commands:
./autogen.sh
make
make install
This installs the libvirt on my system. But there are some issues, I have to run libvirtd
explicitly everytime I reboot my system. And whenever I try to run virt-manager from
terminal, it says "No D-Bus daemon running". But when I do "sudo
virt-manager", it runs fine. Any idea what am I doing wrong?
Thanks.
~Peeyush Gupta
1:21 a.m.
Hi,
Do you still have any libvirt-related packages installed in parallel, or
just your selfcompiled binaries?
On 31.07.2013 07:30, Peeyush Gupta wrote:
Hi,
I am trying to install new libvirt version on Ubuntu 12.04 LTS. Now I downloaded libvirt
1.0.5 from libvirt.org/sources then I issued three commands:
./autogen.sh
make
make install
This installs the libvirt on my system. But there are some issues, I have to run libvirtd
explicitly everytime I reboot my system. And whenever I try to run virt-manager from
terminal, it says "No D-Bus daemon running". But when I do "sudo
virt-manager", it runs fine. Any idea what am I doing wrong?
Thanks.
~Peeyush Gupta
_______________________________________________
libvirt-users mailing list
libvirt-users(a)redhat.com
https://www.redhat.com/mailman/listinfo/libvirt-users
--
Mit freundlichen Grüßen, / Best Regards,
Sven SCHWEDAS
Systemadministrator
TAO Beratungs- und Management GmbH | Lendplatz 45 | A - 8020 Graz
Mail/XMPP: sven.schwedas(a)tao.at | +43 (0)680 301 7167
http://software.tao.at
7:49 a.m.
On 07/30/2013 11:30 PM, Peeyush Gupta wrote:
Hi,
[can you convince your mailer to wrap long lines? Also, it looks like
your mailer is not using proper in-reply-to headers, such that you are
spawning a new thread every time you reply]
I am trying to install new libvirt version on Ubuntu 12.04 LTS. Now I downloaded libvirt
1.0.5 from libvirt.org/sources then I issued three commands:
Any reason you went with 1.0.5 instead of the just-released 1.1.1?
./autogen.sh
This installs the libvirt on my system. But there are some issues, I
have to run libvirtd explicitly everytime
This defaults into installing things into /usr/local, which does not
match the paths your distro normally uses. Your problems may stem from
the fact that because you didn't install it into distro locations, your
distro is unable to run libvirtd as a service. If you run './autogen.sh
--system', that helps prepopulate the configure options such as --bindir
that are more likely to match your distro layout (I know for sure that
./autogen.sh --system matches Fedora layout, but don't know if
Debian-based layout differs, although no one has written a patch
complaining otherwise).
--
Eric Blake eblake redhat com +1-919-301-3266
Libvirt virtualization library http://libvirt.org
12:09 a.m.
Hi,
Sorry, I will keep the instructions in mind.
I tried ./autogen.sh with --system but there was a version mismatch.
I guess someone should write a patch for debian based system.
I tried to install libvirt 1.1.1 with Fedora and when I did make, I got the
following error:
Making all in src
make[2]: Entering directory `/home/peeyush/Downloads/libvirt-1.1.1/src'
GEN libvirt_access_lxc.syms
/bin/sh: -w: command not found
make[2]: *** [libvirt_access_lxc.syms] Error 127
make[2]: Leaving directory `/home/peeyush/Downloads/libvirt-1.1.1/src'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/home/peeyush/Downloads/libvirt-1.1.1'
make: *** [all] Error 2
Any idea why am I getting this?
Thanks.
~Peeyush Gupta
________________________________
From: Eric Blake <eblake(a)redhat.com>
To: Peeyush Gupta <gpeeyush(a)ymail.com>
Cc: "libvirt-users(a)redhat.com" <libvirt-users(a)redhat.com>
Sent: Wednesday, 31 July 2013 6:19 PM
Subject: Re: [libvirt-users] Installing libvirt
On 07/30/2013 11:30 PM, Peeyush Gupta wrote:
Hi,
[can you convince your mailer to wrap long lines? Also, it looks like
your mailer is not using proper in-reply-to headers, such that you are
spawning a new thread every time you reply]
I am trying to install new libvirt version on Ubuntu 12.04 LTS. Now I downloaded libvirt
1.0.5 from libvirt.org/sources then I issued three commands:
Any reason you went with 1.0.5 instead of the just-released 1.1.1?
./autogen.sh
This installs the libvirt on my system. But there are some issues, I
have to run libvirtd explicitly everytime
This defaults into installing things into /usr/local, which does not
match the paths your distro normally uses. Your problems may stem from
the fact that because you didn't install it into distro locations, your
distro is unable to run libvirtd as a service. If you run './autogen.sh
--system', that helps prepopulate the configure options such as --bindir
that are more likely to match your distro layout (I know for sure that
./autogen.sh --system matches Fedora layout, but don't know if
Debian-based layout differs, although no one has written a patch
complaining otherwise).
--
Eric Blake eblake redhat com +1-919-301-3266
Libvirt virtualization library http://libvirt.org
7:59 a.m.
On 07/31/2013 11:09 PM, Peeyush Gupta wrote:
Hi,
Sorry, I will keep the instructions in mind.
I tried ./autogen.sh with --system but there was a version mismatch.
I guess someone should write a patch for debian based system.
I tried to install libvirt 1.1.1 with Fedora and when I did make, I got the
following error:
Making all in src
make[2]: Entering directory `/home/peeyush/Downloads/libvirt-1.1.1/src'
GEN libvirt_access_lxc.syms
/bin/sh: -w: command not found
Can you rerun with 'make V=1' so we can see the full command line that
was attempted? I suspect there is a bug in the makefile that expanded
to nothing based on your platform and the software you have installed
(or not installed).
--
Eric Blake eblake redhat com +1-919-301-3266
Libvirt virtualization library http://libvirt.org
1:11 a.m.
make: *** [all] Error 2
Any idea why am I getting this?
- possible missing a package
- make (verbose++)
- try different versions (1.0.3 ...), use this make-howto [1] (comments are welcome as
mail)
regards Heiko
[1] http://www2.fh-lausitz.de/launic/comp/xen/libvirt/130305.xen.make.libvirt
3:07 a.m.
Hi,
I launched a fresh Fedora 18 VM and did the whole
process again and voila, I dont know how, but it's
working! There was no error and the installation was
successful.
Thanks.
~Peeyush Gupta
________________________________
From: Eric Blake <eblake(a)redhat.com>
To: Peeyush Gupta <gpeeyush(a)ymail.com>
Cc: "libvirt-users(a)redhat.com" <libvirt-users(a)redhat.com>
Sent: Thursday, 1 August 2013 6:29 PM
Subject: Re: [libvirt-users] Installing libvirt
On 07/31/2013 11:09 PM, Peeyush Gupta wrote:
Hi,
Sorry, I will keep the instructions in mind.
I tried ./autogen.sh with --system but there was a version mismatch.
I guess someone should write a patch for debian based system.
I tried to install libvirt 1.1.1 with Fedora and when I did make, I got the
following error:
Making all in src
make[2]: Entering directory `/home/peeyush/Downloads/libvirt-1.1.1/src'
GEN libvirt_access_lxc.syms
/bin/sh: -w: command not found
Can you rerun with 'make V=1' so we can see the full command line that
was attempted? I suspect there is a bug in the makefile that expanded
to nothing based on your platform and the software you have installed
(or not installed).
--
Eric Blake eblake redhat com +1-919-301-3266
Libvirt virtualization library http://libvirt.org
4010
days inactive
4013
days old
6 comments
4 participants
participants (4)
-
Eric Blake -
Heiko L. -
Peeyush Gupta -
Sven Schwedas