Hi everybody,
since long time, I'm using Xen on CentOS with XL, currently latest
CentOS 7 with Xen 4.15 from the CentOS-Xen-Project. For several VMs I
have to use SR-IOV, to lower the CPU-usage on Dom0 on the host.
CentOS 7 comes to an end, Xen is not supported by RHEL nor RockyLinux
anymore, so unfortunately I have to switch to KVM.
First step will be now, converting all the scripts for managing and
running VMs, that they run with the additional libvirt-layer.
Mostly everything is working, but I do not get a network interface in
the VM, when I start it with "virsh start ..." instead of "xl create ...".
First of all, is there documentation how to configure the VMs in the
dom-definition for XEN (all docs I found are KVM-related)?
The converted xl-config does not do the job:
virsh -c xen:/// domxml-from-native --format xen-xl vm > vm.xml
These are some none working examples I tried out:
...
<interface type='hostdev' managed='yes'>
<mac address='02:16:32:10:20:30'/>
<driver name='xen'/>
<source>
<address type='pci' domain='0x0000' bus='0x81' slot='0x02'
function='0x6'/>
</source>
<vlan>
<tag id='11'/>
</vlan>
</interface>
...
...
<hostdev mode='subsystem' type='pci' managed='yes'>
<driver name='xen'/>
<source>
<address domain='0x0000' bus='0x81' slot='0x02' function='0x6'/>
</source>
<address type='pci' domain='0x0000' bus='0x81' slot='0x02'
function='0x6'/>
</hostdev>
...
Result is always the same, the VM does not find any interface to
configure, when starting as libvirt:
# dmesg | egrep -i "net|eth"
...
[ 4.523173] iavf: Intel(R) Ethernet Adaptive Virtual Function Network
Driver - version 4.4.2.1
# lspci | egrep -i "net|eth"
00:00.6 Ethernet controller: Intel Corporation Ethernet Virtual Function
700 Series (rev 02)
# lspci -vmmks 00:00.6
Slot: 00:00.6
Class: Ethernet controller
Vendor: Intel Corporation
Device: Ethernet Virtual Function 700 Series
SVendor: Intel Corporation
SDevice: Device 0000
Rev: 02
Module: i40evf
Module: iavf
NUMANode: 0
# lsmod | egrep -i "iavf|i40"
iavf 135168 0
auxiliary 16384 1 iavf
ptp 20480 1 iavf
# ifconfig eth0
eth0: error fetching interface information: Device not found
The same VM after starting with XL:
# dmesg | egrep -i "net|eth"
...
[ 4.742038] iavf: Intel(R) Ethernet Adaptive Virtual Function Network
Driver - version 4.4.2.1
[ 40.578461] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.642868] iavf 0000:00:00.6 eth0: NIC Link is Up Speed is 10 Gbps
Full Duplex
[ 40.644015] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
# lspci | egrep -i "net|eth"
00:00.6 Ethernet controller: Intel Corporation Ethernet Virtual Function
700 Series (rev 02)
# lspci -vmmks 00:00.6
Slot: 00:00.6
Class: Ethernet controller
Vendor: Intel Corporation
Device: Ethernet Virtual Function 700 Series
SVendor: Intel Corporation
SDevice: Device 0000
Rev: 02
Driver: iavf
Module: i40evf
Module: iavf
NUMANode: 0
# lsmod | egrep -i "iavf|i40"
iavf 135168 0
auxiliary 16384 1 iavf
ptp 20480 1 iavf
# ifconfig eth0
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.20.30.40 netmask 255.255.255.0 broadcast 10.20.30.1
...
ether 02:16:32:10:20:30 txqueuelen 1000 (Ethernet)
I expect, that all the SR-IOV stuff is configured correctly, because the
VMs runs in XL-mode without any problems.
Thanks a lot for any ideas,
--
kind regards,
Thorolf
