- Users - libvirt List Archives

[libvirt-users] assign static external IP to container
by scar 23 Dec '13

23 Dec '13

hello i have a server colocated in a datacenter with several external IP addresses available to use. the physical server is using one of these IPs, and i want to assign another, unused IP to the virtual machine. i thought i could just do this by editing the container's /etc/network/interfaces, setting a static IP address for eth0 much like i did for br0 on the host machine.... but doesn't seem to be working. ifconfig shows eth0 has the external address but i can't resolve any hostnames nor telnet to a direct IP address (no route to host). if i change back to dhcp and let eth0 get an internal address, i can at least access the internet but cannot access the virtual machine from the internet. what is the trick to giving a VM a routable, external IP address? thanks

3 10

[libvirt-users] blockcopy for libvirt and version compatibility
by Mark Trinh 21 Dec '13

21 Dec '13

I'm currently running: virsh --version 1.0.2 libvirtd --version libvirtd (libvirt) 1.0.2 I have a couple questions. 1. Can I upgrade my libvirt.so version to use with an older libvirtd? In other words, does the versions of libvirt and libvirtd need to be in lock step? 2. I'm able to use virsh blockcopy, but I want to do it programmatically via C. I looked through the API and was not able to see any references to that. I did see mention of virDomainBlockCopy on the TIP of the git repository, but no other references to it. How do I run virsh blockcopy via a C function?

2 2

[libvirt-users] About debugging of libvirt.
by cool dharma06 19 Dec '13

19 Dec '13

i am using libvirt-1.1.4 with xen(libxl). When destroying the VM its showing the following error : virsh # destroy 4 error: Failed to destroy domain 4 error: End of file while reading data: Input/output error error: One or more references were leaked after disconnect from the hypervisor error: Failed to reconnect to the hypervisor virsh # list error: failed to connect to the hypervisor error: no valid connection error: Failed to connect socket to '/var/run/libvirt/libvirt-sock': Connection refused already i send one request to this community to solve this problem. they suggested to do gdb. Any guide to do the gdb libvirtd. By googling i did the following things: 1. i enable the logoutput and loglevel in libvirtd.conf 2. restarted the libvirtd with the changed configuration file. 3. ps -aux | grep libvirtd 4. gdb libvirtd pid 5. then what i have to do to find the reason for this error. Suggest me some steps to solve this problem. regards, cooldharma06.

4 8

[libvirt-users] fuse in libivrt-lxc
by Eldar Yusupov 19 Dec '13

19 Dec '13

Hi, I created an LXC domain via libvirt (on Fedora 20), but when I'm trying to mount a FUSE filesystem, like sshfs, I'm getting a following error: $ sshfs 172.30.15.2:/<mntdir> /<mntpoint> fuse: device not found, try 'modprobe fuse' first I see that there's no /dev/fuse device. Is there a way to make it work? Can I get it working via libvirt domain xml file settings or should I use something else, for example, edit cgroups settings directly somehow? Thanks in advance! -- -- Regards, Eldar Yusupov.

2 2

[libvirt-users] QXL and VRAM settings in Virsh/Virt-Manager
by Alex GS 18 Dec '13

18 Dec '13

Hello list, Having a bit of an issue with virt-manager and virsh on Fedora 19/20. I've created several virtual guest machines, one of them is Windows. I've selected QXL and everything is working normally. The only part that's giving me trouble is that I'm unable to set the QXL VRAM higher than 64mb. This would be very useful for performance reasons. I've edited the XML for the corresponding machines and manually set the VRAM higher but when I start the machine with either virsh or virt-manager it defaults to 64mb again. Questions: 1. How can I set the QXL VRAM higher than the default 64mb? 2. Does the VRAM size even matter for guest video performance or does guest video share RAM from the total virtual RAM allocated? Thank you, AGS

1 0

[libvirt-users] BZ1042505: Upon assigning addresses to new virtio-serial ports, libvirt can over-allocate
by Jonathan Lebon 18 Dec '13

18 Dec '13

Hello, (Not sure if this would be better suited for libvir-list, but here it goes!) I filed a bug last week regarding the way in which libvirt assigns addresses to virtio-serial ports. https://bugzilla.redhat.com/show_bug.cgi?id=1042505 To summarize, adding more than 31 ports causes problems because libvirt assigns them all to a single controller, which has a max of 31 (or less if the controller has a ports attribute). I was wondering, in general (eg. for things other than virtio-serial ports), are address assignments done by libvirt considered 'best efforts' (ie. we don't guarantee that it will work) or part of the 'promise' to the [API] user? (Ie. it should always result in a functioning virtual machine) I might be interested in working on a patch for this if it is considered worthwhile. Cheers, Jonathan

1 0

[libvirt-users] How to Position a Network Interface in Physical PCI Slot
by Thiru Murugan 18 Dec '13

18 Dec '13

Hi , I would like to assign a Network Interface card to Physical Slot X in the virtual machine, I have gone through the XML file definition[Now i have some idea on how to position the Network Interface in Logical PCI Slot.] I am NOT interested in using a PCI Pass-through from the Host. currently running Fedora 19 with libvirt 1.2.0 I would like to create an network interface card on Physical Slot 5 so all my network interfaces under the pci-bridge get detected as pci5px Regards Thiru

2 2

[libvirt-users] non trivial question
by Vasiliy Tolstov 17 Dec '13

17 Dec '13

Hi all. I have very special task - i have some vps on kvm, that sometimes needs external support help (administration). But i can't trust external workers and need to known what files are changed. As i understand best of all - create backup before work and after. After that check it for difference and decide apply this work or not. Vps need to run all time. (no downtime for work). How can i do that and what tools i need to use? Is that possible? Thanks for all answers. -- Vasiliy Tolstov, e-mail: v.tolstov(a)selfip.ru jabber: vase(a)selfip.ru

2 1

[libvirt-users] is qemu-kvm really searched for in /usr/bin for KVM?
by Robert P. J. Day 17 Dec '13

17 Dec '13

reading KVM/QEMU hypervisor driver page here: http://libvirt.org/drvqemu.html and one reads, "KVM hypervisor: The driver will probe /usr/bin for the presence of qemu-kvm ...". on my RHEL 6.5 system, qemu-kvm is in /usr/libexec, not /usr/bin. am i misreading something? rday

3 3

[libvirt-users] First & long question
by Joaquim Barrera 17 Dec '13

17 Dec '13

Hello everybody! /(First I need to apologize becase I mussunderstood the prupose of libvirt-list and I sent this mail there instead of this list)/ I would like to introduce myself, as this is my first contact with libvirt mailing list (although I've been reading quite a lot of documentation). My name is Joaquim Barrera, from Barcelona, Catalonia. I am a computer engineer and recently I joined a research group here in the university. My task is related to VM migration and management, and since then (a couple of months) I've been trying to figure some things up. Now I need to go one step forward, and I would like to set up a nice dev environment to try some modifications we want to make to libvirt, such as new API or migration-related-stuff. Although I am familiar with linux environrment and programming, I am not really quite familiar with this kind of, may I say, professional development, and there are some issues I need to solve before start writting code. Some of this issues you'll find not relevant or newbie stuff, but I assure you I tried lots of times before coming here. :-) Here is what I got following the instructions in http://libvirt.org/compiling.html $ ./autogen.sh --system $ make After make finishes I have compiled 1.2.0 libvirt in the source tree, and if I execute 'sudo ./run tools/virsh version' I get a this answer: /Compiled against library: libvirt 1.2.0// //Using library: libvirt 1.2.0// //Using API: QEMU 1.2.0// //Running hypervisor: QEMU 1.5.0/ (/note that now I need to run virsh with sudo, I don't know exactly why/) So far, so good. I guess that, with --system flag, 1.2.0 custom libvirt uses config files from standard directories such as /etc/libvirt/libvirtd.conf, and if I used a custom directory instead, I would have to redefine my VMs, am I right? Problems come when I want to use custom 1.2.0 daemon. If I execute "sudo service libvirt-bin stop" followed by "./daemon/libvirtd -d", then custom virsh gives me this error: /error: failed to connect to the hypervisor// //error: no valid connection// //error: Failed to connect socket to '/var/run/libvirt/libvirt-sock': No such file or directory/ And I need to kill custom daemon and restart 1.1.1 libvirtd to recover from this. Any advice? Finally (sorry about this large mail), there is one thing that does bother me quite a lot. Using custom virsh, command history seems to vanish, as I press Arrow-UP and I get "^[[A" in the screen, instead of last command used. Tell me, please, that this is just some silly config I need to adjust... :_( The final comment is, am I following the right direction to be able to develop something with libvirt? :_) Ok, that's all for now, thank you A LOT for your time. Joaquim.

3 5

[libvirt-users] ANNOUNCE: ruby-libvirt 0.5.1
by Chris Lalancette 16 Dec '13

16 Dec '13

I'm pleased to announce the release of ruby-libvirt 0.5.1. ruby-libvirt is a ruby wrapper around the libvirt API. The changelog between 0.5.0 and 0.5.1 is: * Fixes to compile against older libvirt * Fixes to compile against ruby 1.8 Version 0.5.1 is available from http://libvirt.org/ruby: Tarball: http://libvirt.org/ruby/download/ruby-libvirt-0.5.1.tgz Gem: http://libvirt.org/ruby/download/ruby-libvirt-0.5.1.gem It is also available from rubygems.org; to get the latest version, run: $ gem install ruby-libvirt As usual, if you run into questions, problems, or bugs, please feel free to mail me (clalancette(a)gmail.com) and/or the libvirt mailing list. Thanks to everyone who contributed patches and submitted bugs.

1 0

[libvirt-users] centos6 "system checkpoint"
by Ask Stack 15 Dec '13

15 Dec '13

Hello ### http://www.redhat.com/archives/libvir-list/2012-July/msg00782.htm "it almost sounds like you want the convenience of a system checkpoint (the ability to revert to a guest with its RAM state unchanged, which is much faster than booting from just disk state)." ### I am trying to figure out if it is possible to take a snapshot or "system checkpoint" for a VM running on a centos 6 host. I am able to take a snapshot but unable to revert. Force revert will cause the VM to become unresponsive. Nothing would show in console after revert. My host OS environment is CentOS release 6.4 (Final) libvirt-0.10.2-29 qemu-kvm-0.12.1.2-2.415 virsh # suspend combo01 Domain combo01 suspended virsh # snapshot-create-as --domain combo01 combo01-snap1 "snap1-desc" --atomic Domain snapshot combo01-snap1 created virsh # snapshot-list combo01 Name Creation Time State ------------------------------------------------------------ combo01-snap1 2013-12-14 20:57:41 +0000 paused virsh # snapshot-revert combo01 combo01-snap1 error: revert requires force: Target device address type none does not match source pci virsh # snapshot-revert combo01 combo01-snap1 --force virsh # list Id Name State ---------------------------------------------------- 8 combo01 paused virsh # resume combo01 Domain combo01 resumed virsh # console combo01 Connected to domain combo01 Escape character is ^] The VM became unresponsive at this point.

1 0

[libvirt-users] virsh attach makes qcow2 format disk to raw format
by lyz_pro＠163.com 14 Dec '13

14 Dec '13

Hi all I have a problem when I use `virsh attach` to attach a qcow2 disk to vm without argument --subdirver=qcow2 and this makes the qcow2 disk become a raw format disk, and the data in this disk is missing in guest os and also I have used guestmout to confirm this, the same result. Is there any way to let me find back the data in this disk ? the version of libvirt and kvm is : Compiled against library: libvir 0.9.8 Using library: libvir 0.9.8 Using API: QEMU 0.9.8 Running hypervisor: QEMU 1.0.0 Best Regards Li Yuezhou

3 2

[libvirt-users] SAS HBA address and SCSI passthrough
by Corinna Vinschen 12 Dec '13

12 Dec '13

Hi, For some time now (starting with the 3.10 or 3.11 kernels, but I'm not sure) I have the following problem: I have a machine with 6 SATA slots and two SAS controllers, one onboard HBA and one RAID controller in a PCIe slot. The problem is that the order of the SAS controllers changes randomly after a reboot, so the SCSI addresses of the devices change. One time lsscsi prints (empty lines and ellipsis added for clarity): $ lsscsi [0:0:0:0] disk ATA INTEL SSDSC2BA20 5DV1 /dev/sda [6:0:0:0] disk SmrtStor TXA2D20200GA6001 KT00 /dev/sdb [...] [6:0:7:0] tape TANDBERG LTO-4 HH U619 /dev/st0 [6:0:8:0] enclosu Intel RES2SV240 0d00 - [7:0:0:0] disk LSI 9750-8i DISK 5.12 /dev/sdh [7:0:2:0] disk LSI 9750-8i DISK 5.12 /dev/sdi After the next reboot it looks like this: $ lsscsi [0:0:0:0] disk ATA INTEL SSDSC2BA20 5DV1 /dev/sda [6:0:0:0] disk LSI 9750-8i DISK 5.12 /dev/sdb [6:0:2:0] disk LSI 9750-8i DISK 5.12 /dev/sdc [8:0:0:0] disk SmrtStor TXA2D20200GA6001 KT00 /dev/sdd [...] [8:0:7:0] tape TANDBERG LTO-4 HH U619 /dev/st0 [8:0:8:0] enclosu Intel RES2SV240 0d00 - That's really a problem. One of them, not so much a libvirt problem, is the fact that existing command line tools to maintain HBAs and RAID controllers access controller and devices via the host address. The other problem is with libvirt. If you want to access an arbitrary SAS device from a VM, you have to specify the address of the device as SCSI address. Consider this case in a VM xml file to attach to the host's tape drive: <hostdev mode='subsystem' type='scsi' managed='no' sgio='unfiltered'> <source> <adapter name='scsi_host6'/> <address bus='0' target='7' unit='0'/> </source> </hostdev> With the current behaviour of the kernel, this will be broken in all setups with multiple controllers. If the host adapter address changes arbitrarily after a reboot, the VM will have a broken link to the SCSI device. In the worst case, it will access another device connected to another controller and data on that other device may be destroyed. I asked elsewhere how to fix the order of the SAS controllers, but the only information I got was that it's apparently a deliberate choice to initialize HW in parallel, because the OS doesn't care for the order, and thus, the host address of the controllers. Sure, I can create a wrapper script and systemd foo to workaround this issue by creating the xml file content on the fly after a reboot, but, honestly, that can't be a *solution* for this behaviour. As far as I can see, it's kind of impossible to stick to the SCSI address for SCSI devices in the VM XML description. If the VM setup should survive a reboot in a multi-HBA environment, it's necessary to use unambiguous OS device names, like the udev entries under /dev/disk and /dev/tape(*). Is that already possible, or is there some work in progress? Or *is* there some way to make sure that the SAS controllers always have the same host bus address after reboot so libvirt doesn't get into trouble? Thanks, Corinna (*) But then again, assuming I want to import the enclosure at SCSI address [X:0:8:0] into a VM? /dev/sg9? But, no, this isn't unambiguous either. So... what? -- Corinna Vinschen Cygwin Maintainer Red Hat

1 0

[libvirt-users] internal error: unexcepted domain type lxc, excepted one of these: qemu, kqemu, kvm, xen
by Florian Klink 12 Dec '13

12 Dec '13

Hi, I'm not able to create lxc domains anymore with libvirt 1.2.0-1. The current arch linux package is affected by this bug: https://bugs.archlinux.org/task/38007) vm.xml: <domain type="lxc"> <name>test</name> <memory unit="GiB">2</memory> <os> <type>exe</type> <init>/sbin/init</init> </os> <devices> <filesystem type="mount"> <source dir="/var/lib/libvirt/filesysystems/test"/> <target dir="/"/> </filesystem> <interface type="network"> <source network="default"/> </interface> <console type="pty"/> </devices> </domain> # virsh create vm.xml error: Failed to create domain from vm.xml error: internal error: unexcepted domain type lxc, excepted one of these: qemu, kqemu, kvm, xen However, ./configure reports that LXC support is compiled in: configure: Drivers configure: configure: Xen: no configure: QEMU: yes configure: UML: yes configure: OpenVZ: yes configure: VMware: yes configure: VBox: yes configure: XenAPI: no configure: xenlight: no configure: LXC: yes configure: PHYP: yes configure: ESX: yes configure: Hyper-V: no configure: Parallels: no configure: Test: yes configure: Remote: yes configure: Network: yes configure: Libvirtd: yes configure: Interface: yes configure: macvtap: yes configure: virtport: yes configure: configure: Storage Drivers configure: configure: Dir: yes configure: FS: yes configure: NetFS: yes configure: LVM: yes configure: iSCSI: no configure: SCSI: yes configure: mpath: yes configure: Disk: yes configure: RBD: no configure: Sheepdog: no configure: Gluster: no Do you have any idea why it does not work anymore? I don't see any new changes in src/conf/domain_conf.c where the error is thrown (line 10960) on current git HEAD... Florian

2 2

[libvirt-users] guest daemon reading kvmclock - is it not needed or bad idea ?
by Edoardo Comar 12 Dec '13

12 Dec '13

Hi (apologies for the previous post in html - was scrubbed in the list digest) I've dug various posts and articles on host-guest time synchronization. I could not conclude why it might be better to use ntpd in a guest rather than a daemon that reads from kvmclock and having NTP running on the host only (assuming the guest OS is a recent linux and so the clock source is set to the paravirtualized kvm PVclock). any clarifications are welcome, thanks! Edoardo Comar Unless stated otherwise above: IBM United Kingdom Limited - Registered in England and Wales with number 741598. Registered office: PO Box 41, North Harbour, Portsmouth, Hampshire PO6 3AU

1 0

[libvirt-users] guest daemon reading kvmclock - not needed/ bad idea ?
by Edoardo Comar 11 Dec '13

11 Dec '13

1 0

[libvirt-users] assign static public IP to container
by scar 11 Dec '13

11 Dec '13

hello i have a server colocated in a datacenter with several external IP addresses available to use. the physical server is using one of these IPs, and i want to assign another, unused IP to the virtual machine. both the host and guest are running ubuntu server 12.04. i found someone else asking the same thing[1] for CentOS, but i already have a bridge setup so not sure if it pertains... either way the instructions provided are for a different OS. i followed these instructions[2] for setting up my bridge. anyway, i thought i could just do this by editing the container's /etc/network/interfaces, setting a static IP address for eth0 much like i did for br0 on the host machine.... but doesn't seem to be working. ifconfig shows eth0 has the public address but i can't resolve any hostnames nor telnet to a direct IP address (no route to host). if i change back to dhcp and let eth0 get a private address, i can at least access the internet but cannot access the virtual machine from the internet. what is the trick to giving a VM a routable, public IP address? thanks 1. https://www.redhat.com/archives/libvirt-users/2011-December/msg00056.html 2. https://help.ubuntu.com/12.04/serverguide/network-configuration.html#bridgi…

2 5

[libvirt-users] Determine ongoing shutdown via libvirt or preventing migrations to host
by Ondřej Kunc 11 Dec '13

11 Dec '13

Hi list, Is there any function in libvirt to determine runlevel of host or any possibility to prevent VM migrations to that host ? I'm developing simple cluster of 4 servers running KVM VMs. For management I decided to use python-libvirt. It is working in that way, that every VM is diskless and booting via PXE so I can run it on every host server. Every VM has assigned one host as monitor which is responsible to periodically check, that VM is running on one of other hosts. If it don't run, it will be started on first available server assigned for that VM. When one of hosts is shut down, it will migrate all VMs to another hosts, but that monitor which checks VMs will migrate it after reboot. But I have race condition there that monitors can check that host is running before it is shutdown and will migrate VM's back to server which will reboot. Thank you for any help -- Ondřej Kunc, Senior Linux Administrator IGNUM s.r.o., Vinohradská 190, Praha 3, 130 61, CZE Mobil: +420 603 111 111 | Fax: +420 296 332 222 www.ignum.cz | www.domena.cz | www.webcloud.cz

2 3

Re: [libvirt-users] gentoo linux, problem starting vm´s when cache=none
by Daniel P. Berrange 11 Dec '13

11 Dec '13

On Tue, Dec 10, 2013 at 03:21:59PM +0100, Marko Weber | ZBF wrote: > Hello Daniel, > > Am 2013-12-10 11:23, schrieb Daniel P. Berrange: > >On Tue, Dec 10, 2013 at 11:20:35AM +0100, Marko Weber | ZBF wrote: > >> > >>hello mailinglist, > >> > >>on gentoo system with qemu-1.6.1, libvirt 1.1.4, libvirt-glib-0.1.7, > >>virt-manager 0.10.0-r1 > >> > >>when i set on virtual machine "cache=none" in the disk-menu, the > >>machine faults to start with: > >> > >><< > >>Fehler beim Starten der Domain: Interner Fehler: Prozess während der > >>Verbindungsaufnahme zum Monitor beendet :qemu-system-x86_64: > >>-drive file=/raid6/virtual/debian-kaspersky.img,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native: > >>could not open disk image /raid6/virtual/debian-kaspersky.img: > >>Invalid argument > >> > >> > >>Traceback (most recent call last): > >> File "/usr/share/virt-manager/virtManager/asyncjob.py", line 100, > >>in cb_wrapper > >> callback(asyncjob, *args, **kwargs) > >> File "/usr/share/virt-manager/virtManager/asyncjob.py", line 122, > >>in tmpcb > >> callback(*args, **kwargs) > >> File "/usr/share/virt-manager/virtManager/domain.py", line 1210, > >>in startup > >> self._backend.create() > >> File "/usr/lib64/python2.7/site-packages/libvirt.py", line 708, in > >>create > >> if ret == -1: raise libvirtError ('virDomainCreate() failed', > >>dom=self) > >>libvirtError: Interner Fehler: Prozess während der > >>Verbindungsaufnahme zum Monitor beendet :qemu-system-x86_64: > >>-drive file=/raid6/virtual/debian-kaspersky.img,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native: > >>could not open disk image /raid6/virtual/debian-kaspersky.img: > >>Invalid argument > >>>> > >> > >>when i switch back to cache=default, the machine start like a charm. > >> > >>any ideas why? i cant find anything in logs, only this "invalid > >>argument". > > > >cache=none uses O_DIRECT flag. if you get "Invalid argument" it usually > >means that your filesystem is bad and does not support O_DIRECT > > i use vanilla-kernel 3.10.23 and xfs on the partition where the vm > .img is lying. > > the mount options i use: /raid6 type xfs > (rw,noatime,nodiratime,largeio,nobarrier,logbsize=256k) > > any wrong here? XFS should support O_DIRECT, but possibly one of the mount option is causing trouble. I don't know enough about XFS to answer for sure. BTW, please keep your replies on the mailing list... Regards, Daniel -- |: http://berrange.com -o- http://www.flickr.com/photos/dberrange/ :| |: http://libvirt.org -o- http://virt-manager.org :| |: http://autobuild.org -o- http://search.cpan.org/~danberr/ :| |: http://entangle-photo.org -o- http://live.gnome.org/gtk-vnc :|

1 0

[libvirt-users] gentoo linux, problem starting vm´s when cache=none
by Marko Weber | ZBF 10 Dec '13

10 Dec '13

hello mailinglist, on gentoo system with qemu-1.6.1, libvirt 1.1.4, libvirt-glib-0.1.7, virt-manager 0.10.0-r1 when i set on virtual machine "cache=none" in the disk-menu, the machine faults to start with: << Fehler beim Starten der Domain: Interner Fehler: Prozess während der Verbindungsaufnahme zum Monitor beendet :qemu-system-x86_64: -drive file=/raid6/virtual/debian-kaspersky.img,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native: could not open disk image /raid6/virtual/debian-kaspersky.img: Invalid argument Traceback (most recent call last): File "/usr/share/virt-manager/virtManager/asyncjob.py", line 100, in cb_wrapper callback(asyncjob, *args, **kwargs) File "/usr/share/virt-manager/virtManager/asyncjob.py", line 122, in tmpcb callback(*args, **kwargs) File "/usr/share/virt-manager/virtManager/domain.py", line 1210, in startup self._backend.create() File "/usr/lib64/python2.7/site-packages/libvirt.py", line 708, in create if ret == -1: raise libvirtError ('virDomainCreate() failed', dom=self) libvirtError: Interner Fehler: Prozess während der Verbindungsaufnahme zum Monitor beendet :qemu-system-x86_64: -drive file=/raid6/virtual/debian-kaspersky.img,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native: could not open disk image /raid6/virtual/debian-kaspersky.img: Invalid argument >> when i switch back to cache=default, the machine start like a charm. any ideas why? i cant find anything in logs, only this "invalid argument". the machine is created with profile "linux / debian squeeze" cause its a debian 6 marko

2 1

[libvirt-users] ANNOUNCE: ruby-libvirt 0.5.0
by Chris Lalancette 10 Dec '13

10 Dec '13

All, I'm pleased to announce the release of ruby-libvirt 0.5.0. ruby-libvirt is a ruby wrapper around the libvirt API. Version 0.5.0 brings new APIs, more documentation, and bugfixes: * Updated Network class, implementing almost all libvirt APIs * Updated Domain class, implementing almost all libvirt APIs * Updated Connection class, implementing almost all libvirt APIs * Updated DomainSnapshot class, implementing almost all libvirt APIs * Updated NodeDevice class, implementing almost all libvirt APIs * Updated Storage class, implementing almost all libvirt APIs * Add constants for almost all libvirt defines * Improved performance in the library by using alloca Version 0.5.0 is available from http://libvirt.org/ruby: Tarball: http://libvirt.org/ruby/download/ruby-libvirt-0.5.0.tgz Gem: http://libvirt.org/ruby/download/ruby-libvirt-0.5.0.gem It is also available from rubygems.org; to get the latest version, run: $ gem install ruby-libvirt As usual, if you run into questions, problems, or bugs, please feel free to mail me (clalancette(a)gmail.com) and/or the libvirt mailing list. Thanks to everyone who contributed patches and submitted bugs. Chris Lalancette

1 0

[libvirt-users] Question about setns recognising in libvirt autoconf
by hzguanqiang＠corp.netease.com 09 Dec '13

09 Dec '13

Hi experts, When I test lxc container with lxc-enter-namespace command, It reported an error as following: root@debian:~/github/libvirt# vir lxc-enter-namespace lxc --noseclabel /bin/df -hl error: Cannot get namespaces for 3145: Function not implemented It seems that setns is not supported by my kernel. But from the following info, It seemed the reason is just libvirt/autoconf doesn't recgonise setns. root@debian:~/github/libvirt# grep setns /proc/kallsyms ffffffff8105b78b T SyS_setns ffffffff8105b78b T sys_setns root@debian:~/github/libvirt# ./configure | grep setns checking for setns... no What the problem really is ? How can I fix this problem? Thanks~ ------------------ Best regards! GuanQiang 2013-12-09

2 4

[libvirt-users] Libvirt support for KVM/ARM
by 林佳緯 09 Dec '13

09 Dec '13

Sorry for ask the similar question again. ( I have asked "libvirt support for arm platform" but truely I want to ask libvirt for kvm/arm.) My question: Does libvirt API support KVM/ARM now? Thanks for any answer. Gavin

1 0

[libvirt-users] assign static external IP to container
by scar 09 Dec '13

09 Dec '13

hello i have a server colocated in a datacenter with several external IP addresses available to use. the physical server is using one of these IPs, and i want to assign another, unused IP to the virtual machine. i thought i could just do this by editing the container's /etc/network/interfaces, setting a static IP address for eth0 much like i did for br0 on the host machine.... but doesn't seem to be working. ifconfig shows eth0 has the external address but i can't resolve any hostnames nor telnet to a direct IP address (no route to host). if i change back to dhcp and let eth0 get an internal address, i can at least access the internet but cannot access the virtual machine from the internet. what is the trick to giving a VM a routable, external IP address? thanks

1 0