- Users - libvirt List Archives

[libvirt-users] NetworkManager and bridged networking
by Gene Czarcinski 23 Aug '14

23 Aug '14

Adam Williamson (adamw) has done a fine job at determining how to get bridged networking working with NetworkManager: https://www.happyassassin.net/2014/07/23/bridged-networking-for-libvirt-wit… According to Adam, he did the work on Fedora 21 whereas I did it on Fedora 20. the undesirable features (problems) I found may be corrected on F21 but I believe that they have not been fixed. While Adam's procedure for creating a bridge definition for NetworkManager using the Gnome or nm-connection-editor are basically correct. However, The virt-manager & libvirt do not "like" the default names. [*not a show stopper but it should be fixed*] Instead, the the bridge definition, use "br0" for the connection name and the device name. For the "slave" definition (the real physical NIC), use the <physical_device_name> such as p33p1 or p4p1 or em0 or whatever. I then rebooted the host to make sure everything was clean and the netowrk came up fine on br0. Then, using virt-manager, I took an existing VM, deleted the virtual NIC, added a new virtual NIC using br0. After booting up the VM, you need to edit its network configuration to delete the existing definition and add a new one pointing to the new virtual NIC. This works!!! And on Fedora 20 ... oops, not quite Fedora 20. This was done on a Fedora 20 host which as the updates from fedora-virt-preview applied. I still have a system without the preview updates so I will go back and see if it works or it needs the preview updates. Gene

1 0

[libvirt-users] vlan tags filtered in linux bridge interfaces?
by Dennis Jacobfeuerborn 22 Aug '14

22 Aug '14

Hi, I've set up a virtual machine and plugged it into a bridge on the host. When i configure an ip for eth0 in the guest i can ping other machines fine but when I add an interface eth0.10 in the guest and add an ip pings using this interface do not work. When using tcpdump in vnet0 on the host I can see the icmp packets when I ping using eth0 in the guest but not when I use the eth0.10 interface. Do tagged packets get filtered by libvirt and can this be disabled so that packets just get forwarded without such filtering? Regards, Dennis

2 1

[libvirt-users] How to enable SELinux driver for libvirt?
by Qiang Guan 22 Aug '14

22 Aug '14

Hi guys, It seems libvirt disable SELinux driver by default. How to enable SELinux driver for libvirt? -- ------------ Jackie Best Regards

2 3

[libvirt-users] virt-sandbox-service
by Gene Czarcinski 21 Aug '14

21 Aug '14

Is there any documentation/tutorial that explains how to use virt-sandbox-service? After looking at some writeups about virt-sandbox-service, this looks like a good tool for something I need to do. But, following the "examples" I cannot get anything to work correctly. With a simple xfce install with httpd, lighttpd, and libvirt-sandbox installed, I tried: 1. virt-sandbox-service create -C -u lighttpd.service webserver1 which produced a python traceback?? 2. virt-sandbox-service create -C -u httpd.service webserver2 Which appeared to work correctly but when I tried: virt-sandbox-service start webserver2 I got an error message saying that "start" was not valid??? 3. On another system with lighttpd and httpd already installed and able to run, I updated libvirt and friends to the preview version. My virtual systems seem to run OK. I then installed libvirt-sandbox and tried: virt-sandbox-service create -C -u httpd.service tstserver which got some error messages about sockets. I assume that this stuff has to work for someone. HELP! Gene

1 1

[libvirt-users] virsh snapshot
by Adam King 21 Aug '14

21 Aug '14

Hi, I had a 'domain' called APP03. I was performing auto snapshots each night using /usr/bin/virsh snapshot-create APP03 . I then wanted the domain to be called APP01 for clarity's sake, so I did virsh dumpxml APP03 > APP03.xml, edited the name to APP01 and changed the ID. I then did virsh define APP03.xml to get APP01. I have now realised that the qcow2 images are huge (1.1TB image but 80G inside the virtual machine), I am assuming this is the snapshots tagged onto the virtual hard disk? How do I reduce the size of those back to something realistic? I've removed old snapshots from APP03 using virsh snapshot-delete APP03 '<snapshotidnumber> Hope this makes sense

2 5

[libvirt-users] Reboot, halt, poweroff called inside an lxc domain
by Michal Witanowski 21 Aug '14

21 Aug '14

Hi all, Is there any possibility (using libvirt C API or whatever else) to "propagate" shutdown events (reboot, halt, power off) to a host? The API seems to lack this functionality - there exists function virConnectDomainEventRegisterAny, but the virDomainEventStoppedDetailType enum does not distinguish between these 3 different situations. Moreover, while rebooting a machine, an additional argument can be passed to reboot() syscall, which will be used by bootloader during the startup. Ideally, when calling e.g. "reboot recovery" inside an lxc container I'd like to be informed (inside host) that "reboot" was called with "recovery" as additional argument, so I can take appropriate actions. Thanks in advance. Best regards, Michal

2 1

[libvirt-users] failed to initialize directx in w7
by arnaud gaboury 21 Aug '14

21 Aug '14

I am not sure this issue is tight to Red Hat qxl GPU driver, but I can't initialize directxX on a guest windows 7. Trying to start a game, I get the error message : Failed to initialize directX Of course, directX is installed on the w7 guest, and properly. The dxdiag command, a directx diagnostic tool, does not show any error. Some summary under the video : Driver name : Red Hat QXL GPU Processor type : SeaBIOS VBEC(C) 2011 No Directx functionality are available (Direct Draw, Direct3D, AGP texture) I am not a windows expert, but I would like to know if DirectX is compatible with QXL driver. If not, what is the process to be able to run directX on the windows guest ? If both are compatible, what did I miss ? The VM is working perfectly with virtio & qxl. Please find below my virt-install command: ----------------------------- virt-install --connect qemu:///system --name=tintinWinoz --memory 4096 --cpu host-model-only --os-variant=win7 --disk /myVM/tintin --boot cdrom,hd --virt-type kvm --graphics spice --controller scsi,model=virtio-scsi --cdrom /dev/cdrom --disk /drawer/myIso/w7.iso,device= cdrom ----------------------------------------------------- I thereafter installed manually from the w7 guest virtio & qxl drivers. Thank you for advises.

1 0

[libvirt-users] Libvirt Java API to get CPU usage of VM (KVM)
by Restituto Marcus Arevalo 20 Aug '14

20 Aug '14

Hi all libvirt-users, Is there a counterpart on Java of the function virDomainGetCPUStats that is based on C API? Because I am trying to create a program based on java to get the CPU usage of a Guest/Domain/VM in KVM using the Libvirt Java API. Honestly, I am having a hard time in starting my program. I have no idea where to start. I mean, what functions do I need to get the CPU usage of the guest/domain in KVM? I know there are other options but I am avoiding in connecting to the VM through SSH and get the CPU usage. To make things easier to understand, I need to know how the Virtual Machine Manager in Linux is able to output a graph of the CPU usage of EACH VM. I really need help. I have no idea where to start. Any suggestions would be much appreciated. I'll try to post a screenshot of the graph later. regards, Marco

2 1

[libvirt-users] disable-ticketing
by mhd 20 Aug '14

20 Aug '14

hi... where usually disable-ticketing is avaliable in vm xml ???? i use this command virsh edit vmname and i can edit any options and added but when add this option to <graphics> as example : <graphics disable-ticketing='yes'> or <graphics> <disable-ticketing /> </graphics> nothing happened the file return to first status only this option ... if i add passwd in <graphics> is took as example: <graphics passwd='111111'> it's work and vm xml is edited...

3 2

[libvirt-users] virt-install: failed to initialize KVM: Permission denied
by arnaud gaboury 20 Aug '14

20 Aug '14

As a regular user, member of the libvirt group, I run this command to create a basic VM: virt-install --connect qemu:///system --name=test --ram 2048 --cpu host-model-only --os-variant=win7 --disk /myVM/test --boot cdrom,hd --virt-type kvm --graphics spice --controller scsi,model=virtio-scsi --cdrom=/drawer/myIso/w8.iso It returns an error : --------------------------------- Starting install... ERROR internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied failed to initialize KVM: Permission denied --------------------------------- $ getfacl /dev/kvm # file: dev/kvm # owner: root # group: kvm user::rw- user:martinus:rw- group::rw- mask::rw- other::--- The command return seems to indicate rights are correct. $ lsmod return kvm & kvm_intel are loaded. If I run the virt-install with qemu:///session, I do not have this issue and can create the VM. I found many entries about the KVM permission issue, but with no clear answer to solve it. Thank you for any suggestion -- google.com/+arnaudgabourygabx

2 1