- Users - libvirt List Archives

[libvirt-users] Full documentation for virsh?
by David Ehle 06 May '10

06 May '10

Hello, Does anyone know where full documentation for virsh can be found? Or if the there are any plans to update the man page? The man page lists far fewer commands than virsh lists from its interactive mode when you type help. I noticed this when I was trying to figure out the difference between pool-destroy, and pool-delete. The help entries in the virsh shell are not very informative: virsh # help pool-destroy NAME pool-destroy - destroy a pool SYNOPSIS pool-destroy <pool> DESCRIPTION Destroy a given pool. OPTIONS <pool> pool name or uuid virsh # help pool-delete NAME pool-delete - delete a pool SYNOPSIS pool-delete <pool> DESCRIPTION Delete a given pool. OPTIONS <pool> pool name or uuid ... unless you already know how virsh defines delete vs destroy. (anyone care to explain it to me?) The word pool does not occur in the virsh man page for Ubuntu Karmic release at least. Thanks for the great list!

3 2

[libvirt-users] libvirtd loses all of its data after restart
by guido 06 May '10

06 May '10

Hi, I'm having a problem with libvirtd (backend being kvm) losing its if I restart it with /etc/init.d/libvirtd restart. What I did was: Start libvirtd Connect to it using virsh Create a new storage pool with pool-create-as Create some volumes with vol-create-as Create some virtual machines with create Restart libvirtd using /etc/init.d/libvirtd restart Reconnect with virsh After this, all the previously defined pools, volumes and virtual machines would no longer be listed with pool-list or list, respectively. (list --all doesn't show anything either) The virtual machines I had started earlier are still running and I can still connect to them using vnc, but obviously, I can no longer manage them using libvirt. Why is this happening? Is libvirtd's data not supposed to be persistent? Is this maybe just an old bug? How can I get the still running virtual machines back under control? The system I'm using for this is a recently installed CentOS 5.4 with libvirt-0.6.3-20.1.el5_4 installed directly from its package repository. The only changes I made from the vanilla install was to install and configure some SSL certs in /etc/libvirt/libvirtd.conf, as described on the libvirt website and to enable LIBVIRTD_ARGS="--listen" in /etc/sysconfig/libvirtd. Guido -- Too much multitasking isn't good for you.

2 2

[libvirt-users] weird "no supported architecture for os type 'hvm'"
by Claude Noshpitz 06 May '10

06 May '10

Hi, I have two identical machines with exactly the same CentOS 5.4 kickstarted from the same sources, and the same packages installed. Their cpuinfos are identical, and they are running libvirt 0.6.3 with the very same libvirtd.conf. Yet... One of them works fine, the other says "no supported architecture for os type 'hvm'" for the same template (attached) and image. Any thoughts on what kind of defect or misconfiguration could cause this? Thanks much! --Claude

1 1

[libvirt-users] FYI: Notes on setting up KVM guests using iSCSI
by Daniel P. Berrange 05 May '10

05 May '10

DV suggested that we document some libvirt setups using shared storage. I'm not a fan of NFS, so I wrote some blog posts on how to use iSCSI in the context of libvirt + KVM. There is of course more than one way todo things, so I've outlined a couple of different options. One completely manual command line approach using tgtadm on the iSCSI server: http://berrange.com/posts/2010/05/05/provisioning-kvm-virtual-machines-on-i… ..and virsh/virt-install on the KVM host http://berrange.com/posts/2010/05/05/provisioning-kvm-virtual-machines-on-i… Then one completely GUI based approach, using a QNAP NAS as the iSCSI server http://berrange.com/posts/2010/05/04/provisioning-kvm-virtual-machines-on-i… ..and a virt-manager on the KVM host: http://berrange.com/posts/2010/05/04/provisioning-kvm-virtual-machines-on-i… You can of course mix+match, doing the iSCSI server the manual way and the libvirt bits the GUI way and vica-verca. Any other commercial iSCSI server will have the same concepts so the libvirt instructions apply in all likely scenarios. Regards, Daniel -- |: Red Hat, Engineering, London -o- http://people.redhat.com/berrange/ :| |: http://libvirt.org -o- http://virt-manager.org -o- http://deltacloud.org :| |: http://autobuild.org -o- http://search.cpan.org/~danberr/ :| |: GnuPG: 7D3B9505 -o- F3C9 553F A1DA 4AC2 5648 23C1 B3DF F742 7D3B 9505 :|

3 7

[libvirt-users] Building & Installing on OpenSolaris
by gary mazzaferro 04 May '10

04 May '10

Hi, I'm revisiting my libVirt install for opensolaris. I downloaded libvirt 0.8.0.. This is a bit embarassing, but I forgot how to build libVirt on opensolaris. (It's been a while) I'm currently stuck with the configure script failing to find linux kernel headers. Error: "configure: error: You must install kernel-headers in order to compile libvirt" Can anyone post the instructions to build under opensolaris? cheers, gary

4 7

[libvirt-users] libvirt with qemu-kvm, not recognizing NIC model
by Jonathan Hoover 04 May '10

04 May '10

Is this the right list for this question, or should I be elsewhere? I am trying to specify a network card "model type" of "pcnet" (to emulate vmware esxi's network card). No matter what I put for model type in my xml config file, it comes up as an Intel e1000. I ran "qemu-kvm -net nic,model=? /dev/null" and I got back a list of supported models including pcnet,e1000,virtio, and others as expected. No matter which I put in my xml file for /etc/libvirt/qemu/Symantec-bg.xml (a Symantec Brightmail Gateway virtual machine), I just get back that its an Intel card on boot (which doesn't work with Symantec BG). I am running Fedora 12, kernel is 2.6.31.6-166.fc12.x86_64. The version of libvirt is 0.7.1. I am running it on an Intel Core 2 Quad CPU Q8400 @ 2.66 GHz. I have the same problem under Fedora 13 Beta. Thoughts? Jonathan Hoover

1 0

[libvirt-users] using shared storage with libvirt/KVM?
by David Ehle 03 May '10

03 May '10

I apologize if this is a duplicate. I submitted it before I was a list member and it looks like it went into limbo. Dear Moderator, please discard the original if it is sitll in a moderation queue. Hello, I've spent a few days googling and reading documentation, but I'm looking for clarification and advise on setting up KVM/libvirt with shared storage. I have 2 (for now) Ubuntu Karmic systems with KVM/virsh/virt-manager set up and running. I have a storage server that can do NFS/iSCSI/samba/ etc. I am trying to figure out the best way to set things up so that I can run several (eventually) production linux guests (mostly debian stable) on the 2 KVM host systems and be able to migrate them when maintenance is required on their hosts. Performance is of medium importance, stability/availibilty is pretty high priority. A common opinion seems to be that using LVs to hold disk images gives possibly the best IO performance, followed by raw, then qcow2. Would you agree or disagree with this? What evidence can you provide? I am also rather confused about using shared storage, and what options can be combined with this. I have succesfully made an iscsi device available to libvirt/virsh/virt-manager via an XML file + pool-define + pool-start. However the documentation states that while you can create pools through libvirt, volumes have to be pre-allocated: http://libvirt.org/storage.html "Volumes must be pre-allocated on the iSCSI server, and cannot be created via the libvirt APIs." I'm very unclear on what this means in general, and specifically how you preallocate the the Volumes. When I make a iscsi pool available via something like this: <pool type="iscsi"> <name>virtimages</name> <source> <host name="iscsi.example.com"/> <device path="demo-target"/> </source> <target> <path>/dev/disk/by-path</path> </target> </pool> In virt-manger I can see it as a pool, but when I try to select it for where to create an image, it uses the pool AS A Volume (I think). That brings me to my next question/misunderstanding... If you are using shared storage (via NFS or iSCSI) does that also mean you MUST use a file based image rather than an LVM LV? NFS makes directories available, not devices. You can make an unformated "raw" LV available via iSCSI, but its not seen on the far side as a LV but instead as a scsi disk which you need to partition. You can make a PV>VG>LV out of that and then make your new LV available to libvirt/KVM but then your stacking a heck of a lot of LVM/LVs/partion tables up which seems pretty dubious. I'm also not sure that the stack would be visable/available to the second system using that iSCSI device. (I'm pretty new to using iSCSI as well.) Redhat provides pretty good documentation on doing shared storage/live migration for NFS: http://www.redhat.com/docs/en-US/Red_Hat_Enterprise_Linux/5.4/html/Virtuali… But unfortunately the section on Shared Storage with iSCSI is a bit lacking: "9.1. Using iSCSI for storing guests This section covers using iSCSI-based devices to store virtualized guests." and thats it. For maybe 6-10 guests, should I simply just be using NFS? Is its performance that much worse than iSCSI for this task? So since KVM/libvirt is getting used quite often in production now - but some simple things are not making any sense to me - I'm guessing that I have some really basic misunderstandings of how to do shared storage / Pools/ Volumes for migration. Would one of the kind readers of this least be willing to correct me? Please CC to my original email address as well as I am not yet a regular subscriber. Thanks again! David.

2 2

[libvirt-users] Issues after migrating from Xen to KVM
by Ralf Hornik Mailings 03 May '10

03 May '10

Dear list, I have moved my HVMs from xen to kvm and it worked well except some problems using virsh. First, one OpenSolaris HVM does boot with warnings: WARNING: /pci@0,0/pci1af4,1100@1,2 (uhci1): No SOF interrupts have been received, this USB UHCI host controller is unusable* *The corresponding process: /usr/bin/qemu-system-x86_64 -S -M pc-0.12 -enable-kvm -m 1024 -smp 1,sockets=1,cores=1,threads=1 \ -name server01 -uuid e382c360-23bd-b400-0b89-9a1e69613ec4 -nographic \ -nodefaults -chardev socket,id=monitor,path=/usr/local/libvirt/var/lib/libvirt/qemu/server01.monitor,server,nowait \ -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/dev/xen_vol/xen_opensol,if=none,id=drive-ide0-0-0,boot=on \ -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive file=/dev/hde,if=none,id=drive-ide0-0-1 \ -device ide-drive,bus=ide.0,unit=1,drive=drive-ide0-0-1,id=ide0-0-1 -device rtl8139,vlan=0,id=net0,mac=00:16:3e:28:85:7a,bus=pci.0,addr=0x4 \ -net tap,ifname=tap0,vlan=0,name=hostnet0 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3 This does not happen when I boot with plain qemu-bin: /usr/local/kvm/bin/qemu-system-x86_64 -hda /dev/xen_vol/xen_opensol \ -hdb /dev/hde -net nic,macaddr=00:16:3e:28:85:7a \ -net tap,ifname=tap0 -nographic \ -m 1024 -daemonize Second is one Centos 5.2 HVM that does not boot at all. However when I boot manually and omitt "-S" and "-nodefaults" then it comes up. I looked for the -S option and I wonder why it is being used by default. Can anybody help me? I cannot see any further documentation about the "-nodefault" option and how to disable "-S" Best regards Ralf

2 2

Re: [libvirt-users] Windows Vista Client Fails to Connect to Ubuntu libvirtd
by Matthias Bolte 03 May '10

03 May '10

2010/4/30 Tim McLeod <tim.mcleod(a)simulamen.eu>: > Requesting urgent assistance if I may? > > Attempting to connect to an Ubuntu machine using an MinMG compiled virsh on > a Windows Vista machine. Using insecure TCP simply to prove a concept to a > client. However, cannot connect; situation as follows: > > Edited /etc/libvirt/libvirt.conf as follows: > listen_tcp = 1 > auth_tcp = "none" > > Edited /etc/default//libvirt-bin as follows: > libvirt-opts="-d -l" Did you restart libvirtd after the changes and checked that it's started successfully? listen_tls defaults to 1 in /etc/libvirt/libvirt.conf, in combination with the -l flag (short for --listen) libvirtd requires properly configured SSL certificates. If libvirtd can't find the certificates or fails to validate them then it won't start up. You can disable TLS in /etc/libvirt/libvirt.conf by setting listen_tls = 0 and restart libvirtd. > Running virsh on Vista client fails as follows: > $ virsh -c qemu+tcp://192.168.1.101/system > error: unable to connect to libvirtd at '192.168.1.101': errno=10061 > error: failed to connect to the hypervisor > > Running virsh on Ubuntu server fails as follows: > $ virsh -c qemu+tcp:///system > Connecting to uri: qemu+tcp:///system > error: unable to connect to libvirtd at 'localhost': Connection refused > error: failed to connect to the hypervisor Once libvirtd is running and configured properly for TCP transport then remote and local TCP access to libvirtd works for me. > Indeed, with libvirt-opts="-d -l" in etc/default//libvirt-bin the 'default' > command also fails: > $ virsh -c qemu:///system > Connecting to uri: qemu:///system > error: unable to connect to 'var/run/libvirt/libvirt-sock': Connection > refused > error: failed to connect to the hypervisor > Local access to libvirtd using qemu:///system requires properly configured polkit, or running virsh as root. This is independent from the -d and -l flags. Matthias

2 1

[libvirt-users] Windows Vista Client Fails to Connect to Ubuntu libvirtd
by Development 01 May '10

01 May '10

Requesting urgent assistance if I may? Attempting to connect to an Ubuntu machine using an MinMG compiled virsh on a Windows Vista machine. Using insecure TCP simply to prove a concept to a client. However, cannot connect; situation as follows: Edited /etc/libvirt/libvirt.conf as follows: listen_tcp = 1 auth_tcp = "none" Edited /etc/default//libvirt-bin as follows: libvirt-opts="-d -l" Running virsh on Vista client fails as follows: $ virsh -c qemu+tcp://192.168.1.101/system error: unable to connect to libvirtd at '192.168.1.101': errno=10061 error: failed to connect to the hypervisor Running virsh on Ubuntu server fails as follows: $ virsh -c qemu+tcp:///system Connecting to uri: qemu+tcp:///system error: unable to connect to libvirtd at 'localhost': Connection refused error: failed to connect to the hypervisor Indeed, with libvirt-opts="-d -l" in etc/default//libvirt-bin the 'default' command also fails: $ virsh -c qemu:///system Connecting to uri: qemu:///system error: unable to connect to 'var/run/libvirt/libvirt-sock': Connection refused error: failed to connect to the hypervisor Suggestions very welcome... Tim McLeod

2 1