- Users - libvirt List Archives

[libvirt-users] Issues with libvirt virtual networking
by Joshua Atkinson 19 Nov '15

19 Nov '15

Hello all, I am having issues getting my virtual network to work correctly. As of current, I have set up a virtual network with virt-manager, using the routed mode to forward network traffic. I have found guests can see/ping themselves, the host's virtual IP and the host's real IP, but nothing else. Guests fail to see any other device on the real network or the internet. My host is Arch Linux on Linux 4.2.5-1 with the VFIO kernel, and runs a QEMU/KVM hypervisor. My main guest runs a new install of Windows 10, with the virtio network interface. I have only one virtual network configured, and no network interfaces configured in virt-manager. Does anyone know why my VMs cannot see anything other than themselves and the host? My iptables rules (entirely set by libvirt): Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.100.0/24 ACCEPT all -- 192.168.100.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:bootpc Output of "brctl show" bridge name bridge id STP enabled interfaces virbr0 8000.52540012f3ab yes virbr0-nic Output of "ip addr": 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: enp5s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether 90:2b:34:68:84:c0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.8/24 brd 192.168.1.255 scope global enp5s0 valid_lft forever preferred_lft forever inet6 fe80::922b:34ff:fe68:84c0/64 scope link valid_lft forever preferred_lft forever 3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default link/ether 52:54:00:12:f3:ab brd ff:ff:ff:ff:ff:ff inet 192.168.100.1/24 brd 192.168.100.255 scope global virbr0 valid_lft forever preferred_lft forever 4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel master virbr0 state DOWN group default qlen 500 link/ether 52:54:00:12:f3:ab brd ff:ff:ff:ff:ff:ff Many Thanks, Josh

1 0

[libvirt-users] Vm not booting up after manual migration
by Sakhi Hadebe 19 Nov '15

19 Nov '15

Hi, I have two hosts installed with libvirt. We have just installed a latest version of libvirt on one of the hosts, version Compiled against library: libvirt 1.2.16 Using library: libvirt 1.2.16 Using API: QEMU 1.2.16 Running hypervisor: QEMU 2.3.0 The host hosting all our virtual machines runs an older version Compiled against library: libvirt 1.2.2 Using library: libvirt 1.2.2 Using API: QEMU 1.2.2 Running hypervisor: QEMU 2.0.0 I am now trying to manually migrate virtual machines to the host with the newest version of libvirt. I have copied the qcow2, img, and xml files of all the virtual machines to this host. The problem I am encounting is that the newer version uses "Host device eno1:macvtap" network source for its virtual interface, whisch is not the same as "Host device vnet18 (Bridge "br0")" in the older version. Not sure if this is something \i have to worry about. I have manuall copied all the files across, but when booting up the vm on the newset version ost it hangs up before booting (see screenshot attached). Please help me to fully boot up into this virtual machine. -- Regards, Sakhi Hadebe Engineer: South African National Research Network (SANReN)Competency Area, Meraka, CSIR Tel: +27 12 841 2308 <+27128414213> Fax: +27 12 841 4223 <+27128414223> Cell: +27 71 331 9622 <+27823034657> Email: sakhi(a)sanren.ac.za <shadebe(a)csir.co.za>

1 0

[libvirt-users] blockcopy pauses vm
by Fırat KÜÇÜK 19 Nov '15

19 Nov '15

Hello, I want to live migrate qcow disk image. virsh snapshot-create-as --domain my-vm migration-snapshot \ --diskspec vda,file=/opt/n0-n1/my-vm-snapshot.img \ --disk-only --atomic --no-metadata virsh undefine my-vm virsh blockcopy --domain my-vm vda \ /opt/n0-n1/my-vm.img \ --wait --verbose --timeout 3600 I check the copy status with "virsh blockjob my-vm vda". After %92 VM pauses and I cannot resume it.

2 1

[libvirt-users] regard limiting network bandwidth
by asw Anose 19 Nov '15

19 Nov '15

hi all i am a kvm , qemu user newbie , i am using libvirt and virsh to mange my KVM VMs , i want to limit the network bandwidth of each VM , i come across libvirt xml format option : <forward mode='nat' dev='eth0'/> <bandwidth> <inbound average='1000' peak='5000' burst='5120'/> <outbound average='128' peak='256' burst='256'/> </bandwidth>to limit the bandwidth of each vm , however i have a question how does these option applied limit on kvm vm ? through using of linux cgroub or its a qemu network bandwidth limit functionality ?

2 1

[libvirt-users] "Allocate entire disk now" with an existing virtual disk
by Boylan, Ross 19 Nov '15

19 Nov '15

Have I just overwritten some of my virtual drive, and if so, is there a way to recover? On a linux host I use LVM logical volumes as the backing for my virtual disks. Using the Virtual Machine Manager 0.9.1 GUI I did this: 1. select source machine, go into details, select virtual disk and removed the hardware. 2. select destination machine, go into details, add storage. 3. click "select managed or other existing storage" 4. click the browser button under it, and select the volume detached from the source machine 5. set device type to virtio. 6. click finish. Both VM's were off, and the source VM used virtio also. KVM is the hypervisor. There were actually 2 drives, and so I repeated the steps above twice, except that the second time I clicked on "Allocate entire disk now", which deselected it (I hope) before step 6. The destination machine already had disks. So, did I just overwrite one of the disks? If so, is there a way to recover? The reason I suspect a problem is that, although the partition tables appear intact on both virtual drives, the filesystem does not. Within the virtual machine 1 partition from each drive is combined in a volume group. The main logical volume group on that fails to mount: root@jessie01:~# mount -o ro /dev/markov02/root /mnt/markov02 mount: wrong fs type, bad option, bad superblock on /dev/mapper/markov02-root, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so. and e2fsck says root@jessie01:~# e2fsck /dev/markov02/root e2fsck 1.42.12 (29-Aug-2014) /dev/markov02/root: recovering journal Superblock needs_recovery flag is clear, but journal has data. It's possible this has nothing to do with the option to allocate the entire disk, since the source VM was having problems anyway (that's why I moved the disks). However, I'm pretty sure I was able to access the filesystem both in the source VM and in an earlier round when I move the disks to the destination. Thanks. Ross Boylan

1 0

[libvirt-users] virDomainCoreDumpWithFormat files created as root
by NoxDaFox 18 Nov '15

18 Nov '15

Greetings, I am dumping a guest VM memory for inspection using the command "virDomainCoreDumpWithFormat" and the created files appear to belong to root (both user and group). I have searched around but didn't find any answer. Is there a way to instruct QEMU to create those files under a different user? Thank you.

5 7

[libvirt-users] Add host
by Sakhi Hadebe 18 Nov '15

18 Nov '15

Hi, I have two host machines both installed with libvirt and virt-manager, which provides me with GUI. I have virtual machines running in one of the host. Now I want to migrate some of the virtual machines to the other machines. I am trying to migrate using the Virtual Machine Manager. When I select migrate, it pops up a window to choose the new host. The dropdown menu to choose the new host for the virtual machine is empty. How do you add the new host to the other, so they can know each other? Does it require a clustering software to achieve that? I need some assistance in that regard -- Regards, Sakhi Hadebe Engineer: South African National Research Network (SANReN)Competency Area, Meraka, CSIR Tel: +27 12 841 2308 <+27128414213> Fax: +27 12 841 4223 <+27128414223> Cell: +27 71 331 9622 <+27823034657> Email: sakhi(a)sanren.ac.za <shadebe(a)csir.co.za>

2 2

[libvirt-users] Telling virt-manager to re-read ~/.gconf in RHEL 6
by Digimer 16 Nov '15

16 Nov '15

Hi all, I've written a tool that configured Virtual Machine Manager, but I've got a condition that I am now sure how to handle... If the user isn't logged in and I configure their ~/.gconf/apps/virt-manager/*, and then they log in, everything works great. However, if they've already logged in and there was no prior virt-manager configuration, the custom config is overwritten and lost when the user logs out. Similarly, if VMM is closed, I write the config and then they open VMM (again, having logged into gnome where there was no ~/.gconf/apps/virt-manager), it acts like there is no configuration (it tries to auto-connect to localhost and doesn't show the remote machines). I am guessing this behaviour is a because VMM doesn't check it's configuration file after logging into gnome (either at all, or at least when there was no config at gnome login). Is there a way I can tell virt-manager to re-check the config? Thanks! -- Digimer Papers and Projects: https://alteeve.ca/w/ What if the cure for cancer is trapped in the mind of a person without access to education?

3 2

[libvirt-users] Qemu-ga on Windows 10
by Dominique Ramaekers 14 Nov '15

14 Nov '15

Hi, I have a windows 10 guest with qemu-ga-x64.msi installed from the fedora virtio iso. qemu-ga version is 0.12.1 host qemu version is 2.1.0 (I know its older but in this version the active block commit works perfectly...) libvirt version 1.2.12 I have these lines in my xml: <channel type='unix'> <source mode='bind' path='/var/lib/libvirt/qemu/channel/target/PCVIRTmbe.org.qemu.guest_agent.0'/> <target type='virtio' name='org.qemu.guest_agent.0' state='disconnected'/> <alias name='channel0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> /var/lib/libvirt/qemu/channel/target/PCVIRTmbe.org.qemu.guest_agent.0 exists on the host and the rights seems to be all right. On the guest, the folder C:\ProgramData\qemu-ga exists Still, I can't start the qemu-ga service. I get this error: Can't start QEMU GuestAgent-service on the local computer Error 1053: The service didn't answer correctly on the start command (or something like this, the error message in in Dutch) If I start the qemu-ga from the cmd I get this error: error opening path error opening channel failed to create guest agent channel failed to initialize guest agent channel Does anybody got an idea how to resolve this problem? Thanks in advance. Dominique.

1 1

[libvirt-users] How to fix an incorrect storage pool?
by Phill Edwards 14 Nov '15

14 Nov '15

I've created my storage pool incorrectly. I'm using LVM and I have a volume group called vms-lvm. When I look at it in virt-manager I see that the volumes it contains are home, root and swap, so when I created the storage group in virt-manager I must have specified something incorrectly. Unfortunately I can't find a way to correct this. If I try to destroy (stop) the storage group I get an error: # virsh pool-destroy vms-lvm error: Failed to destroy pool vms-lvm error: internal error: Child process (/usr/sbin/vgchange -aln centos_hyv2) unexpected exit status 5: Logical volume centos_hyv2/swap in use. Can't deactivate volume group "centos_hyv2" with 3 open logical volume(s) Same if I try to undefine it: # virsh pool-undefine vms-lvm error: Failed to undefine pool vms-lvm error: Requested operation is not valid: storage pool 'vms-lvm' is still active Can anyone please advise how I get out of this mess? There must surely be a way of undefining this?

2 3