- Users - libvirt List Archives

[libvirt-users] Errors while using blkiotune command
by Saurabh Deochake 23 Mar '13

23 Mar '13

Hi all, I want to limit the I/O bandwidth inside the container, so I used virsh command blkiotune. But when I enter a command: virsh # blkiotune lxcguest --weight 250 I get following errors: error: Unable to change blkio parameters error: Requested operation is not valid: blkio cgroup isn't mounted I also have blkio cgroup mounted. What can be the problem? Thanks in advance. Regards, Saurabh Deochake

4 6

[libvirt-users] [bump] Storage pool created on the "wrong" vg
by Alaric Haag 22 Mar '13

22 Mar '13

________________________________ From: Alaric Haag Sent: Tuesday, March 19, 2013 2:39 PM To: libvirt-users(a)redhat.com Subject: Storage pool created on the "wrong" vg Hello all, (Hopefully, I am posing this question to the correct list!) I seem to have mis-clicked through the creation of an LVM-based storage pool in virt-manager and it is using a volume group containing LVs dedicated to the root/swap filesystems. As these are active LVs, there seems no way to remove this pool. Is that true? My reading thus far suggests that, with LVM storage units, you can't delete them from the pool without REALLY deleting them from the VG. I'm "new enough" to KVM to be missing something obvious, but I'd be pretty shocked if a "structure" like a storage pool can't be deconstructed. Kind regards, Alaric ------------------------ Here's a bit more detail in the hope someone might help: I clicked through the creation of a storage pool, and accidentally used the wrong volume group, so I have: virsh # vol-list vm_pool Name Path ----------------------------------------- lv_root /dev/vg_01/lv_root lv_swap /dev/vg_01/lv_swap These two LVs, in group vg_01, are the / and swap partition of the host system. I meant for the pool to reside on vg_vm, a different volume group. Can I safely run: virsh # vol-delete lv_root --pool=vm_pool virsh # vol-delete lv_swap --pool=vm_pool virsh # pool-delete vm_pool or do the first two steps actually destroy the LVs in vg_01 thus bringing my system crashing down? The link below strongly suggests I cannot delete these logical volumes from the pool, but is a "draft" for OpenSUSE. (I'm running libvirt 0.10.2-18 on RHEL6) http://doc.opensuse.org/products/draft/SLES/SLES-kvm_sd_draft/cha.libvirt.s… If that's the case, is there ANY way to undo my mistake and remove this pool? I am most grateful for any guidance! Alaric

1 0

Re: [libvirt-users] remote connection issue 'virsh -c qemu+ssh:///root@localhost/system list'
by Javi Legido 21 Mar '13

21 Mar '13

Hi Olivia. Another think that you should check is socat package. In my documented example the hypervisor running KVM is a Debian squeeze, and I had to proceed this way: sudo aptitude update; sudo aptitude install netcat socat -R sudo vim /bin/netcatsocket #!/bin/bash socat - unix-client:$2 sudo chmod +x /bin/netcatsocket You can try it and see if it helps or not. PD: looping in again the list, I replied just to Olivia before Cheers El 21/03/2013 12:47, "Yin Olivia-R63875" <r63875(a)freescale.com> escribió: > Hi Javier, > > Thanks for your help. > From the pages you provided, I guess you suggest is as below: > * Cannot recv data: Host key verification failed. : Connection reset by > peer > > Sucede al lanzar: > > virt-manager -c qemu+ssh://usuario@hipervisor/system > > Solucion: iniciar una sesion SSH para almacenar las claves del hipervisor > en el cliente: > > ssh usuario@hipervisor > > Exactly, I've login with ssh and then connect with virsh. > > user@x86:~$ ssh root(a)10.193.20.109 > root(a)10.193.20.109's password: > root@ppc:~# exit > logout > Connection to 10.193.20.109 closed. > > user@x86:~$ virsh -c qemu+ssh://root@10.193.20.109/system list --all > root(a)10.193.20.109's password: > error: failed to connect to the hypervisor > error: End of file while reading data: nc: invalid option -- 'U' > BusyBox v1.19.4 (2013-03-08 13:08:18 CST) multi-call binary. > > Usage: nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]: > Input/output error > > It still failed to connect the hypervisor, instead of ssh issue. > > Best Regards, > Olivia > > > -----Original Message----- > > From: javilegido(a)gmail.com [mailto:javilegido@gmail.com] On Behalf Of > Javi > > Legido > > Sent: Thursday, March 21, 2013 7:35 PM > > To: Yin Olivia-R63875 > > Subject: Re: [libvirt-users] remote connection issue 'virsh -c > > qemu+ssh:///root@localhost/system list' > > > > Hi Olivia. > > > > It's in spanish, but pretty easy to follow, maybe it helps you: > > > > > http://wiki.legido.com/doku.php?id=informatica:linux:virtualizacion:kvm#adm > > inistrar_kvm_y_vm_desde_una_gui_en_el_cliente > > > > With this guide you should be able to connect from a client machine (for > > instance your laptop) to the hypervisor (KVM) if both have SSH > connectivity. > > > > Cheers. > > > > Javier > > > > 2013/3/21 Yin Olivia-R63875 <r63875(a)freescale.com>: > > > Hi, > > > > > > I'm trying remote connection with qemu hypervisor on FSL PPC board. > > > > > > The libvirt server is the PPC board. > > > > > > root@ppc:~# ifconfig eth0 10.193.20.109 root@ppc:~# libvirtd -d > > > root@ppc:~# virsh -c qemu:///system define test.xml root@ppc:~# virsh > > > -c qemu:///system start test root@ppc:~# virsh -c qemu:///system list > > > --all > > > Id Name State > > > ---------------------------------------------------- > > > 2 test running > > > > > > Connect from an X86 PC (Ubuntu 10.04) to the PPC board. > > > > > > user@x86:~$ virsh -c qemu+ssh://root@10.193.20.109/system list --all > > > The authenticity of host '10.193.20.109 (10.193.20.109)' can't be > > established. > > > RSA key fingerprint is 2f:56:07:08:da:7d:ac:41:45:57:d2:12:15:19:67:e0. > > > Are you sure you want to continue connecting (yes/no)? yes > > > root(a)10.193.20.109's password: > > > error: failed to connect to the hypervisor > > > error: End of file while reading data: Warning: Permanently added > > '10.193.20.109' (RSA) to the list of known hosts. > > > nc: invalid option -- 'U' > > > BusyBox v1.19.4 (2013-03-08 13:08:18 CST) multi-call binary. > > > > > > Usage: nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]: > > > Input/output error > > > > > > > > > > > > I tried to verify the remote connection on localhost. But it also > failed > > as below: > > > > > > root@mpc8572ds:~# virsh -c qemu+ssh:///root@localhost/system list > > > --all root@localhost's password: > > > error: failed to connect to the hypervisor > > > error: End of file while reading data: nc: invalid option -- 'U' > > > BusyBox v1.19.4 (2013-03-08 13:08:18 CST) multi-call binary. > > > > > > Usage: nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]: > > > Input/output error > > > > > > > > > Could anyone give suggestion on this issue? > > > > > > > > > Best Regards, > > > Olivia > > > > > > > > > _______________________________________________ > > > libvirt-users mailing list > > > libvirt-users(a)redhat.com > > > https://www.redhat.com/mailman/listinfo/libvirt-users > > >

1 0

[libvirt-users] Libvirt dead, pid still exists
by SHREE DUTH AWASTHI 21 Mar '13

21 Mar '13

Hi All, Refering to the link below, I got to know that previous versions of Libvirtd had this issue. https://www.redhat.com/archives/libvirt-users/2012-August/msg00104.html We are using libvirt-0.10.0 but we are facing the same issue. Procedure to reproduce : 1. Login to some domain name say CLA-0 using virsh. (i) # virsh list --all Id Name State ---------------------------------------------------- 4 CLA-0 running (ii) # virsh console 4 Connected to domain CLA-0 Escape character is ^] 2. Whenever we exit from the above CLA-0 domain by pressing ctrl-] We are getting the Segmentation fault, however core is not generated but we have debugged it through gdb Program received signal SIGSEGV, Segmentation fault. 0x00007ffff5a96c71 in pthread_mutex_lock () from /lib64/libpthread.so.0 (gdb) bt #0 0x00007ffff5a96c71 in pthread_mutex_lock () from /lib64/libpthread.so.0 #1 0x00007ffff78c8b97 in ?? () from /usr/lib64/libvirt.so.0 #2 0x00007ffff78b6297 in ?? () from /usr/lib64/libvirt.so.0 #3 0x00007ffff7865b65 in virHashRemoveEntry () from /usr/lib64/libvirt.so.0 #4 0x00007ffff78b60d0 in ?? () from /usr/lib64/libvirt.so.0 #5 0x00007ffff78c95f9 in ?? () from /usr/lib64/libvirt.so.0 #6 0x00007ffff78ce711 in virStreamAbort () from /usr/lib64/libvirt.so.0 #7 0x000000000042b546 in ?? () #8 0x000000000042b8f3 in ?? () #9 0x00007ffff78c983a in ?? () from /usr/lib64/libvirt.so.0 #10 0x00007ffff7843cc5 in virEventPollRunOnce () from /usr/lib64/libvirt.so.0 #11 0x00007ffff78428f5 in virEventRunDefaultImpl () from /usr/lib64/libvirt.so.0 #12 0x00007ffff793407d in virNetServerRun () from /usr/lib64/libvirt.so.0 #13 0x000000000040c483 in ?? () #14 0x00007ffff534cbbe in __libc_start_main () from /lib64/libc.so.6 ---Type <return> to continue, or q <return> to quit--- #15 0x000000000040b139 in ?? () #16 0x00007fffffffe7d8 in ?? () #17 0x000000000000001c in ?? () #18 0x0000000000000001 in ?? () #19 0x00007fffffffea73 in ?? () #20 0x0000000000000000 in ?? () After this point libvirtd is dead. # service libvirtd status libvirtd dead but pid file exists >From the mail conversation between you and Andrey we came to know that patch has been provided for this problem. Could you please share us the fix. Thanking you in anticipation. Thanks and Regards, Shree Duth Awasthi.

1 0

[libvirt-users] About live migration with snapshots
by Chiang Hubert 21 Mar '13

21 Mar '13

Hello, I'd like to live migration with snapshots. But it doesn't work. It comes out a message "cannot migrate domain with 1 snapshots" Then I try to trace the code(Libvirt 0.9.8 to 1.0.3), I find out the code in src/qemu/qemu_migration.c @ Line 1395 - 1440 (Libvirt 1.0.3) It will check the VM which has snapshots or not. I just curious about this limitation, why the VM can't live migration with snapshots? What happen if I skip this check? Does it has any suggestion way or virsh command with options to do live migration with snapshots? Thanks a lot. Hubert

3 2

[libvirt-users] SSD Trim needed? Physical Block Device Keep Track Of Guest FS Blocks?
by d hee 21 Mar '13

21 Mar '13

I am trying to figure out if a SSD drive needs to receive trim commands from the KVM guest filesystem(strictly Linux ext4 in this case).... When a file is deleted inside a KVM guest(ext4 and raw image)....If a SSD is the underlying block device that the KVM raw disk image resides on, does the SDD drive need to know which block(s) are marked for reuse within the raw image? Or is it since the Guest raw image is a container that the physical hard drive has no concern about the filesystem blocks within the Guest? Meaning the physical disk would only be concerned with the image itself as a whole...such as if the whole image was deleted? Thanks, -Darin

2 1

[libvirt-users] Storage pool created on the "wrong" vg
by Alaric Haag 19 Mar '13

19 Mar '13

Hello all, (Hopefully, I am posing this question to the correct list!) I seem to have mis-clicked through the creation of an LVM-based storage pool in virt-manager and it is using a volume group containing LVs dedicated to the root/swap filesystems. As these are active LVs, there seems no way to remove this pool. Is that true? My reading thus far suggests that, with LVM storage units, you can't delete them from the pool without REALLY deleting them from the VG. I'm "new enough" to KVM to be missing something obvious, but I'd be pretty shocked if a "structure" like a storage pool can't be deconstructed. Kind regards, Alaric

1 0

[libvirt-users] network bridge hairpin parameter support
by Zang MingJie 19 Mar '13

19 Mar '13

Hi: Currently we encounter a problem where OpenStack may forget or misconfig the bridge hairpin setting, and will cause some unexpected behavior [1]. Although this bug is marked fixed, but if we manually restart the vm by virsh will also trigger the problem. And because the bridge interface is created and managed by libvirt, we are considering move the hairpin configuration to libvirt. Now I start writing a patch to achieve this, but after digging into the source code, I found only kvm/qemu and uml backend may support this parameter. Other backends manage their own bridge, and seems no way to modify it. I expect is there any solution working in progress or should we add the new hairpin parameter in libvirt configuration ? [1] https://bugs.launchpad.net/nova/+bug/933640

1 0

[libvirt-users] network bridge hairpin parameter support
by Zang MingJie 19 Mar '13

19 Mar '13

Hi: Currently we encounter a problem where OpenStack may forget or misconfig the bridge hairpin setting, and will cause some unexpected behavior [1]. Although this bug is marked fixed, but if we manually restart the vm by virsh will also trigger the problem. And because the bridge interface is created and managed by libvirt, we are considering move the hairpin configuration to libvirt. Now I start writing a patch to achieve this, but after digging into the source code, I found only kvm/qemu and uml backend may support this parameter. Other backends manage their own bridge, and seems no way to modify it. I expect is there any solution working in progress or should we add the new parameter in libvirt configuration ? [1] https://bugs.launchpad.net/nova/+bug/933640

1 0

[libvirt-users] libvirt rpm src
by Drew Morris 19 Mar '13

19 Mar '13

Hi Guys, Do you know where the source RPMS are for libvirt? Can't find them in the official downloads section. -- Regards, Drew Morris

4 3