January 2013 - Users - libvirt List Archives

[libvirt-users] Cannot get eth0 to work on libvirt-lxc
by Marco Monteiro 19 Jan '13

19 Jan '13

I'm trying to get an Archlinux guest running on a Archlinux host. Everything works except ethernet. When I boot the host, --- # dmesg |tail [ 8.265493] Bridge firewalling registered [ 8.514547] IPv6: ADDRCONF(NETDEV_UP): virbr0: link is not ready [ 8.645303] ip6_tables: (C) 2000-2006 Netfilter Core Team --- Then I do --- # virsh -c lxc:/// start gitolite Domain gitolite started # dmesg |tail [ 348.793398] device veth0 entered promiscuous mode [ 348.793553] IPv6: ADDRCONF(NETDEV_UP): veth0: link is not ready [ 348.997973] IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready [ 348.997998] virbr0: topology change detected, propagating [ 348.998001] virbr0: port 1(veth0) entered forwarding state [ 348.998008] virbr0: port 1(veth0) entered forwarding state [ 348.998017] IPv6: ADDRCONF(NETDEV_CHANGE): virbr0: link becomes ready [ 349.784174] EXT4-fs (xvdg): re-mounted. Opts: (null) --- Then I enter the guest and do --- # ip link 5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000 link/ether 02:00:00:00:00:17 brd ff:ff:ff:ff:ff:ff 7: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN mode DEFAULT link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 --- So, eth0 exists. Now, still in the guest: --- # systemctl start dhcpcd@eth0 A dependency job for dhcpcd(a)eth0.service failed. See 'journalctl -xn' for details. # journalctl -xn -- Logs begin at Sat 2013-01-19 10:50:45 UTC, end at Sat 2013-01-19 10:56:26 UTC Jan 19 10:54:48 gitolite sudo[38]: pam_unix(sudo:session): session opened for us Jan 19 10:54:48 gitolite systemd[1]: Expecting device sys-subsystem-net-devices- -- Subject: Unit sys-subsystem-net-devices-eth0.device has begun with start-up -- Defined-By: systemd -- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel -- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/7d495 -- -- Unit sys-subsystem-net-devices-eth0.device has begun starting up. Jan 19 10:56:18 gitolite systemd[1]: Job sys-subsystem-net-devices-eth0.device/s Jan 19 10:56:18 gitolite systemd[1]: Timed out waiting for device sys-subsystem- -- Subject: Unit sys-subsystem-net-devices-eth0.device has failed -- Defined-By: systemd -- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel -- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02c -- -- Unit sys-subsystem-net-devices-eth0.device has failed. -- -- The result is timeout. Jan 19 10:56:18 gitolite systemd[1]: Dependency failed for dhcpcd on eth0. -- Subject: Unit dhcpcd(a)eth0.service has failed -- Defined-By: systemd -- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel -- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02c -- -- Unit dhcpcd(a)eth0.service has failed. -- -- The result is dependency. --- At this point, nothing new in dmesg. Even though ip link should a eth0 device, the sys-subsystem-net-devices-eth0.device has failed? I don't understand this. This is libvirt 1.0.1 in linux 2.6.11. I tried with both systemd 197 and (thinking that recent changes with device naming could be the problem) with 196. It didn't work on either. The domain configuration is: --- <domain type='lxc'> <name>gitolite</name> <uuid>3122bf1d-11bb-0dd8-be64-7e352b3f8694</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64'>exe</type> <init>/sbin/init</init> </os> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/lib/libvirt/libvirt_lxc</emulator> <filesystem type='mount' accessmode='passthrough'> <source dir='/mnt/gitolite'/> <target dir='/'/> </filesystem> <interface type='network'> <mac address='02:00:00:00:00:17'/> <source network='default'/> </interface> <console type='pty'> <target type='lxc' port='0'/> </console> </devices> </domain> --- I also tried using bridged networking configuration but I see the same problem. What could be causing this? Any ideas? Thanks, Marco

1 0

[libvirt-users] Problems with VM networking on Ubuntu Quantal
by Dale Amon 18 Jan '13

18 Jan '13

I have shifted some VM's to a new server running Quantal and have had a world of trouble. The first one was caused by issues with an apparently compiled in path in their apparmor version which forced VM pools to be in /srv or similar rather than where I wanted them. For now this was not a big issue, and thankfully the server where it would be a big time problem (there are individual drives per major customer or user) is Debian. But... I still have issues. The networking has changed considerably and although I can get my VM running, I cannot reach it. The new quantal machines give you something like this: br0 Link encap:Ethernet HWaddr **** inet addr:10.0.0.xx Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: *****/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 p6p1 Link encap:Ethernet HWaddr **** UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 virbr0 Link encap:Ethernet HWaddr **** inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 vnet0 Link encap:Ethernet HWaddr fe:54:00:84:3c:4f inet6 addr: fe80::fc54:ff:fe84:3c4f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 The VM machine has a static ip on the same network, ie 10.0.0.x. It worked fine on the old server but is not reachable (and cannot connect outward). Forwarding is turned on: cat /proc/sys/net/ipv4/ip_forward 1 The VM has eth0 Link encap:Ethernet HWaddr **** inet addr:10.0.0.xx Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: *****/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 An attempt to ping from the VM to anything outside gives a "Destination host unreachable" message. It has been a long time since I set the old machine up, so I may well have forgotten some step.

2 2

[libvirt-users] how to know one domain is defined or not
by lei yang 18 Jan '13

18 Jan '13

Hi experts I want to write a script to determine one domain named "vm1" is defined or not, if defined, I will undefine it. The question is how could I know it define or not ? Lei

3 3

[libvirt-users] Libvirt node is not getting booted through network with KVM too
by Varun Bhatnagar 17 Jan '13

17 Jan '13

Hi, Sorry for putting the images. Posting this question again. I am trying to boot my node through network with the following configuration (even with KVM it is not getting booted): < domain type='kvm'> < name>Node-2-3</name> < os> < type>hvm</type> < boot dev='network'/> < boot dev='hd'/> < /os> < memory>654321</memory> < vcpu>1</vcpu> < interface type='internal'> < source name='test1'/> < model type='am79c970a'/> < mac address='20:00:00:0F:03:01'/> < /interface> < interface type='internal'> < source name='test2'/> < model type='am79c970a'/> < mac address='20:00:00:0F:03:02'/> < /interface>  < interface type='bridge'> < source bridge='vboxtap0'/> < mac address='20:00:00:0F:03:03'/> < model type='am79c973'/> < /interface> < /domain> But I am getting an error message saying: Fatal: Could not read from the boot medium! System halted. Even my network setting is not getting reflected in the Virtualbox. Can you suggest me what is wrong with this configuration. I think to boot a node from network we need to define a boot server but where shall I add that, I am confused.... Any help will be appreciated. Thanks in advance. Regards, Varun =====-----=====-----===== Notice: The information contained in this e-mail message and/or attachments to it may contain confidential or privileged information. If you are not the intended recipient, any dissemination, use, review, distribution, printing or copying of the information contained in this e-mail message and/or attachments to it are strictly prohibited. If you have received this communication in error, please notify us by reply e-mail or telephone and immediately and permanently delete the message and any attachments. Thank you

2 1

[libvirt-users] firewalld, no dhcp and virsh
by Paul Wouters 17 Jan '13

17 Jan '13

On all of the networks I create, I really don't want libvirt/KVM/virt-manager to do any kind of DHCP. I'm currently using xml files to feed into libvirt via virsh, for example: <network> <name>192_0_1</name> <bridge name='swan01' stp='on' delay='0' /> <mac address='12:00:00:16:16:BA'/> <ip address='192.0.1.127' netmask='255.255.255.0'> </ip> </network> Running this through virsh net-define gives no errors, and virt-manager shows: DHCP Start: disabled DHCP End: disabled But any attempt at starting the network causes: Error starting network '192_0_1': failed to add iptables rule to allow DHCP requests from 'swan01' Traceback (most recent call last): File "/usr/share/virt-manager/virtManager/asyncjob.py", line 96, in cb_wrapper callback(asyncjob, *args, **kwargs) File "/usr/share/virt-manager/virtManager/asyncjob.py", line 117, in tmpcb callback(*args, **kwargs) File "/usr/share/virt-manager/virtManager/network.py", line 82, in start self.net.create() File "/usr/lib64/python2.7/site-packages/libvirt.py", line 2049, in create if ret == -1: raise libvirtError ('virNetworkCreate() failed', net=self) libvirtError: failed to add iptables rule to allow DHCP requests from 'swan01' I narrowed this down to the fact that firewalld was not running. So I guess there are two bugs: 1) when not specifying dhcp ranges in the xml, it should _not_ try to poke DHCP holes. 2) when firewalld is not running, it should perhaps log a warning, but not abort the network start. Paul

2 1

[libvirt-users] Libvirt daemon is not getting started
by Varun Bhatnagar 17 Jan '13

17 Jan '13

Hi, Earlier I was having libvirt-0.7.5 but now I have installed 0.9.8 version of libvirt now. I am trying to start libvirt daemon using the command below but daemon it is not getting started and the PID file is not getting created. Tried /usr/loval/sbin/libvirtd -d option too. In that case I am not getting any error but PID file is not getting created in this case too. /usr/local/sbin/libvirtd 2013-01-16 16:43:53.399+0000: 4070: info : libvirt version: 0.9.8 2013-01-16 16:43:53.399+0000: 4070: error : virCommandWait:2192 : internal error Child process (/usr/sbin/iptables --table mangle --delete POSTROUTING --out-interface virbr0 --protocol udp --destination-port 68 --jump CHECKSUM --checksum-fill) status unexpected: exit status 2 2013-01-16 16:43:53.406+0000: 4070: error : virCommandWait:2192 : internal error Child process (/usr/sbin/iptables --table mangle --insert POSTROUTING --out-interface virbr0 --protocol udp --destination-port 68 --jump CHECKSUM --checksum-fill) status unexpected: exit status 2 2013-01-16 16:43:53.406+0000: 4070: warning : networkAddGeneralIptablesRules:1259 : Could not add rule to fixup DHCP response checksums on network 'default'. 2013-01-16 16:43:53.406+0000: 4070: warning : networkAddGeneralIptablesRules:1260 : May need to update iptables package & kernel to support CHECKSUM rule. 2013-01-16 16:43:54.704+0000: 4070: error : umlStartup:471 : cannot initialize inotify 2013-01-16 16:43:54.704+0000: 4070: error : virStateInitialize:854 : Initialization of UML state driver failed 2013-01-16 16:43:54.704+0000: 4070: error : daemonRunStateInit:1157 : Driver state initialization failed and I am also trying to connect to VMPlayer with the following URL but it is giving the following error message: virsh # connect vmplayer:///session error: Failed to connect to the hypervisor error: Failed to connect socket to '/usr/local/var/run/libvirt/libvirt-sock': No such file or directory Is this because of the daemon, as it is not getting started or because of some other reason? Can anybody suggest any solution for this. I am stuck from past few days and not able to find solution. Any help will be appreciated. Thanks in advance. Regards, Varun =====-----=====-----===== Notice: The information contained in this e-mail message and/or attachments to it may contain confidential or privileged information. If you are not the intended recipient, any dissemination, use, review, distribution, printing or copying of the information contained in this e-mail message and/or attachments to it are strictly prohibited. If you have received this communication in error, please notify us by reply e-mail or telephone and immediately and permanently delete the message and any attachments. Thank you

2 1

[libvirt-users] LibVirt CPU problem
by Michael Beham 16 Jan '13

16 Jan '13

Hi, I´m testing to start a KVM-VM with different CPU settings and I get an weird error when I use the parameter: <cpu mode='host-model'> !! I have a AMD Opteron 4280 CPU, but in the VM, proc/cpuinfo shows me, that I´m using Intel core2duo cpu model T7700 and in the flag-line of proc/cpu the system is listing the svm-flag of AMD?!?! If I use <cpu mode='host-passthrough'> I get the right CPU-model listed in the VM! Anyone an idea why I get the wrong information with host-model? BTW some further information about used versions: LibVirt version is 0.9.12 qemu-kvm 1.0 Kernel 3.3.2 Cheers, Mike

2 1

[libvirt-users] Libvirt node is not getting booted through network
by Varun Bhatnagar 16 Jan '13

16 Jan '13

Hi, I am trying to boot my node through network with the following configuration: But I am getting an error message saying: Even my network setting is not getting reflected in the Virtualbox. Can anyone suggest me what is wrong with this configuration. I think to boot a node from network we need to define a boot server but where shall I add that, I am confused.... Any help will be appreciated. Thanks in advance. Regards, Varun =====-----=====-----===== Notice: The information contained in this e-mail message and/or attachments to it may contain confidential or privileged information. If you are not the intended recipient, any dissemination, use, review, distribution, printing or copying of the information contained in this e-mail message and/or attachments to it are strictly prohibited. If you have received this communication in error, please notify us by reply e-mail or telephone and immediately and permanently delete the message and any attachments. Thank you

2 1

[libvirt-users] A issue about KVM block migration
by 刘基 15 Jan '13

15 Jan '13

Hello everyone, I have a issue about the KVM block migration. Please give me some help. 1) I use the "virsh create" command to start a KVM VM in source machine. 2) And then, I use "virsh migrate" cammand to start a block migration: # virsh migrate --live --copy-storage-all --verbose win7 qemu+ssh:// 186.100.8.136/system root(a)186.100.8.136's password: Migration : [ 93% ] I execute "virsh list" command in source machine, and the result is: #virsh list Id Name State ----------------------------------------------------------- 1 win7 running I can find the corresponding qemu-kvm process in the result of "ps -ef | grep qemu-kvm" in source machine. And I execute "virsh list" command in destination machine, and the result is: #virsh list Id Name State ----------------------------------------------------------- 1 win7 paused 3) But after a few minutes，there have a error: # virsh migrate --live --copy-storage-all --verbose win7 qemu+ssh:// 186.100.8.136/system root(a)186.100.8.136's password: Migration : [ 97% ] error: Unable to read from monitor : Connection reset by peer. I execute "virsh list" command in source machine again, and the result is NULL. I cannot find the corresponding qemu-kvm process in the result of "ps -ef | grep qemu-kvm" in source machine. And I execute "virsh list" command in destination machine again, and the result is NULL. But, when I only use qemu-kvm command not use libvirt, I can test block migration successfully (use qemu-kvm to create a VM, and exec "migrate -b -d xxx" command in qemu-kvm monitor to migrate). The version of libvirt is 1.0.1 and the version of qemu-kvm is 1.2.0 ( 1.2.2 is also have this issue). Please give me some help. How to solve the issue. Thanks a lot. **

2 1

[libvirt-users] libvirt RPC error
by Parakkal, Navin S 11 Jan '13

11 Jan '13

Hi, I'm using qemu+ssh://username@hostname/system as the remote URI. Libvirt seems to be communicating fine until some 2 minutes (we poll every 5 seconds) and then it throws up RPC error and many counters are wrong. But if I collect on localhost the counters seems to be coming fine. Test and testvm are guests on the local machine where as Win8 and Ubuntu* are remote URI's connected through ssh. What causes this error "libvir: RPC error : End of file while reading data: : Input/output error" and how do we fix it ? I've pasted the logfile inline. Localhost from which we are connecting: uname -aLinux iwf0044110 3.2.0-23-generic #36-Ubuntu SMP Tue Apr 10 20:39:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@iwf0044110:/home1/parakkal/COLLABNET_11.10_NEW/hpsw-oa/PA/numsVob/linux/2.2/Linux2.6_64_debug# cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" root@iwf0044110:/home1/parakkal/COLLABNET_11.10_NEW/hpsw-oa/PA/numsVob/linux/2.2/Linux2.6_64_debug# virsh version Compiled against library: libvir 0.9.8 Using library: libvir 0.9.8 Using API: QEMU 0.9.8 Running hypervisor: QEMU 1.0.0 Remote host: root@iwf004461:/home1/parakkal/COLLABNET_11.10_NEW/hpsw-oa/PA/numsVob/linux/2.2# uname -a Linux iwf004461 3.0.0-12-server #20-Ubuntu SMP Fri Oct 7 16:36:30 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux root@iwf004461:/home1/parakkal/COLLABNET_11.10_NEW/hpsw-oa/PA/numsVob/linux/2.2# cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" root@iwf004461:/home1/parakkal/COLLABNET_11.10_NEW/hpsw-oa/PA/numsVob/linux/2.2# virsh version Compiled against library: libvir 0.9.2 Using library: libvir 0.9.2 Using API: QEMU 0.9.2 Running hypervisor: QEMU 0.14.1 Note: libvirt.so not present, using /usr/lib/libvirt.so.0 libvir: error : no connection driver available for No connection for URI xen:/// No Xen on this system NOTE: 1 memory stats available out of 8 libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: QEMU error : Requested operation is not valid: cgroup CPU controller is not mounted NOTE: scheduler type not available libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:07 | testvm | Running 04:23:07 | test | Running 04:23:07 | Win8 | Running 04:23:07 | Ubuntu11.10 | Running 04:23:07 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:18 | testvm | Running 04:23:18 | test | Running 04:23:18 | Win8 | Running 04:23:18 | Ubuntu11.10 | Running 04:23:18 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:25 | testvm | Running 04:23:25 | test | Running 04:23:25 | Win8 | Running 04:23:25 | Ubuntu11.10 | Running 04:23:25 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:32 | testvm | Running 04:23:32 | test | Running 04:23:32 | Win8 | Running 04:23:32 | Ubuntu11.10 | Running 04:23:32 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:40 | testvm | Running 04:23:40 | test | Running 04:23:40 | Win8 | Running 04:23:40 | Ubuntu11.10 | Running 04:23:40 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:47 | testvm | Running 04:23:47 | test | Running 04:23:47 | Win8 | Running 04:23:47 | Ubuntu11.10 | Running 04:23:47 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:23:55 | testvm | Running 04:23:55 | test | Running 04:23:55 | Win8 | Running 04:23:55 | Ubuntu11.10 | Running 04:23:55 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:02 | testvm | Running 04:24:02 | test | Running 04:24:02 | Win8 | Running 04:24:02 | Ubuntu11.10 | Running 04:24:02 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:10 | testvm | Running 04:24:10 | test | Running 04:24:10 | Win8 | Running 04:24:10 | Ubuntu11.10 | Running 04:24:10 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:17 | testvm | Running 04:24:17 | test | Running 04:24:17 | Win8 | Running 04:24:17 | Ubuntu11.10 | Running 04:24:17 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:24 | testvm | Running 04:24:24 | test | Running 04:24:24 | Win8 | Running 04:24:24 | Ubuntu11.10 | Running 04:24:24 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:32 | testvm | Running 04:24:32 | test | Running 04:24:32 | Win8 | Running 04:24:32 | Ubuntu11.10 | Running 04:24:32 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:39 | testvm | Running 04:24:39 | test | Running 04:24:39 | Win8 | Running 04:24:39 | Ubuntu11.10 | Running 04:24:39 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:46 | testvm | Running 04:24:46 | test | Running 04:24:46 | Win8 | Running 04:24:46 | Ubuntu11.10 | Running 04:24:46 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:24:54 | testvm | Running 04:24:54 | test | Running 04:24:54 | Win8 | Running 04:24:54 | Ubuntu11.10 | Running 04:24:54 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:25:01 | testvm | Running 04:25:01 | test | Running 04:25:01 | Win8 | Running 04:25:01 | Ubuntu11.10 | Running 04:25:01 | Ubuntu12.04 | Running libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known libvir: error : internal error getaddrinfo failed for 'iwf004461': Name or service not known 04:25:09 | testvm | Running 04:25:09 | test | Running 04:25:09 | Win8 | Running 04:25:09 | Ubuntu11.10 | Running 04:25:09 | Ubuntu12.04 | Running libvir: RPC error : End of file while reading data: : Input/output error 04:25:16 | testvm | Running 04:25:16 | test | Running 04:25:16 | Win8 | Nostate 04:25:16 | Ubuntu11.10 | Nostate 04:25:16 | Ubuntu12.04 | Nostate libvir: RPC error : End of file while reading data: : Input/output error 04:25:20 | testvm | Running 04:25:20 | test | Running 04:25:20 | Win8 | Nostate 04:25:20 | Ubuntu11.10 | Nostate 04:25:20 | Ubuntu12.04 | Nostate libvir: RPC error : End of file while reading data: : Input/output error 04:25:25 | testvm | Running 04:25:25 | test | Running 04:25:25 | Win8 | Nostate 04:25:25 | Ubuntu11.10 | Nostate 04:25:25 | Ubuntu12.04 | Nostate Regards, Navin P.S. Please use reply all as I'm not subscribed to this list .

2 2