[libvirt] macvtap - no incoming ipv6 traffic processed on kvm host unless i start tcpdump on interface
7:13 a.m.
Dear folks,
I'm using for the first time macvtap interface for my virtual machines in bridged
mode.
VM -> HOST -> Router -> INTERNET
This works fine for ipv4 connectivity.
For ipv6 my virtual machines receive appropriate v6 address from radvd but are not able to
receive answer packages from outside (ping -t -6 google.de was started inside VM).
I see the ping request/response on my router:
14:10:52.147834 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 108, length 40
14:10:52.182073 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 108, length 40
14:10:55.179874 IP6 2a01:198:200:350::2 > 2a00:1450:4001:806::1018: ICMP6, destination
unreachable, unreachable address 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 88
But i do not receive the reply on the VM.
However on the KVM host - when i start a tcpdump on the macvtap interface with
root@s1:~# tcpdump -ni macvtap0 ip6
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on macvtap0, link-type EN10MB (Ethernet), capture size 262144 bytes
14:12:37.134516 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 129, length 40
14:12:37.188529 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ff4e:14eb: ICMP6, neighbor
solicitation, who has 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189040 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > fe80::12fe:edff:fee6:cfa:
ICMP6, neighbor advertisement, tgt is 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189202 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 129, length 40
packages starting to get processed and VM receives replies.
Any idea what is happening here?
Cheers,
Stefan
7:32 a.m.
On Wed, Apr 08, 2015 at 02:13:49PM +0200, Stefan Bauer wrote:
Dear folks,
I'm using for the first time macvtap interface for my virtual machines in bridged
mode.
VM -> HOST -> Router -> INTERNET
This works fine for ipv4 connectivity.
For ipv6 my virtual machines receive appropriate v6 address from radvd but are not able to
receive answer packages from outside (ping -t -6 google.de was started inside VM).
I see the ping request/response on my router:
14:10:52.147834 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 108, length 40
14:10:52.182073 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 108, length 40
14:10:55.179874 IP6 2a01:198:200:350::2 > 2a00:1450:4001:806::1018: ICMP6, destination
unreachable, unreachable address 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 88
But i do not receive the reply on the VM.
However on the KVM host - when i start a tcpdump on the macvtap interface with
root@s1:~# tcpdump -ni macvtap0 ip6
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on macvtap0, link-type EN10MB (Ethernet), capture size 262144 bytes
14:12:37.134516 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 129, length 40
14:12:37.188529 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ff4e:14eb: ICMP6, neighbor
solicitation, who has 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189040 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > fe80::12fe:edff:fee6:cfa:
ICMP6, neighbor advertisement, tgt is 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189202 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 129, length 40
packages starting to get processed and VM receives replies.
Any idea what is happening here?
I'm guessing the promiscuous modes plays its part in this field. You
can try setting the interface to promisc mode manually using 'ip l set
$dev promisc on' and see whether that helps without starting tcpdump.
Also check sysctl -a | grep 'ipv6.*forward'.
Disclaimer: all of that ^^ is just a guess :)
Cheers,
Stefan
--
libvir-list mailing list
libvir-list(a)redhat.com
https://www.redhat.com/mailman/listinfo/libvir-list
7:49 a.m.
On Wed, 2015-04-08 at 14:32 +0200, Martin Kletzander wrote:
I'm guessing the promiscuous modes plays its part in this field.
You
can try setting the interface to promisc mode manually using 'ip l set
$dev promisc on' and see whether that helps without starting tcpdump.
Also check sysctl -a | grep 'ipv6.*forward'.
Thank you for your answer. IIRC forwarding is only required for routing.
I use bridge mode.
You are right - it's working with promiscious mode enabled.
Without:
2a01:198:200:8350:98ec:1708:c82e:a4fb dev br-lan INCOMPLETE
With:
2a01:198:200:8350:98ec:1708:c82e:a4fb dev br-lan lladdr
52:54:00:8e:b9:eb REACHABLE
Is it really required to be enabled all the time to make it work?
Cheers,
Stefan
3:12 a.m.
On 08.04.2015 14:13, Stefan Bauer wrote:
Dear folks,
I'm using for the first time macvtap interface for my virtual machines in bridged
mode.
VM -> HOST -> Router -> INTERNET
This works fine for ipv4 connectivity.
For ipv6 my virtual machines receive appropriate v6 address from radvd but are not able
to receive answer packages from outside (ping -t -6 google.de was started inside VM).
I see the ping request/response on my router:
14:10:52.147834 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 108, length 40
14:10:52.182073 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 108, length 40
14:10:55.179874 IP6 2a01:198:200:350::2 > 2a00:1450:4001:806::1018: ICMP6, destination
unreachable, unreachable address 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 88
But i do not receive the reply on the VM.
However on the KVM host - when i start a tcpdump on the macvtap interface with
root@s1:~# tcpdump -ni macvtap0 ip6
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on macvtap0, link-type EN10MB (Ethernet), capture size 262144 bytes
14:12:37.134516 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > 2a00:1450:4001:806::1018:
ICMP6, echo request, seq 129, length 40
14:12:37.188529 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ff4e:14eb: ICMP6, neighbor
solicitation, who has 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189040 IP6 2a01:198:200:8350:dc8b:cd82:144e:14eb > fe80::12fe:edff:fee6:cfa:
ICMP6, neighbor advertisement, tgt is 2a01:198:200:8350:dc8b:cd82:144e:14eb, length 32
14:12:37.189202 IP6 2a00:1450:4001:806::1018 > 2a01:198:200:8350:dc8b:cd82:144e:14eb:
ICMP6, echo reply, seq 129, length 40
packages starting to get processed and VM receives replies.
Any idea what is happening here?
I mildly recalls seeing a bug like this. The problem was in intel's
kernel driver. A NIC by defaul checks incoming packets whether they
match NIC's MAC. So if a TAP device was created over a NIC, it had to be
put into promisc mode (automatically done by the driver) to allow
different MACs and the check was done in kernel then. But since this
generates too much interrupts, NICs HW was extended and it can be
programmed with multiple MACs to let through. However, there was a bug
which I recall of, that intel driver was not always putting the TAP MAC
into the NIC HW correctly. Obviously, the bug was not visible if the NIC
was put into promisc mode. And this may be what you are seeing. Let me
see if I can find the bug.
Michal
3:18 a.m.
On Thu, 2015-04-09 at 10:12 +0200, Michal Privoznik wrote:
I mildly recalls seeing a bug like this. The problem was in
intel's
kernel driver. A NIC by defaul checks incoming packets whether they
match NIC's MAC. So if a TAP device was created over a NIC, it had to be
put into promisc mode (automatically done by the driver) to allow
different MACs and the check was done in kernel then. But since this
generates too much interrupts, NICs HW was extended and it can be
programmed with multiple MACs to let through. However, there was a bug
which I recall of, that intel driver was not always putting the TAP MAC
into the NIC HW correctly. Obviously, the bug was not visible if the NIC
was put into promisc mode. And this may be what you are seeing. Let me
see if I can find the bug.
That sounds like my problem even though i do not have an Intel nic.
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
Cheers,
Stefan
3:39 a.m.
On Thu, 2015-04-09 at 10:12 +0200, Michal Privoznik wrote:
I mildly recalls seeing a bug like this. The problem was in
intel's
kernel driver. A NIC by defaul checks incoming packets whether they
match NIC's MAC. So if a TAP device was created over a NIC, it had to be
put into promisc mode (automatically done by the driver) to allow
different MACs and the check was done in kernel then. But since this
generates too much interrupts, NICs HW was extended and it can be
programmed with multiple MACs to let through. However, there was a bug
which I recall of, that intel driver was not always putting the TAP MAC
into the NIC HW correctly. Obviously, the bug was not visible if the NIC
was put into promisc mode. And this may be what you are seeing. Let me
see if I can find the bug.
FYI - enabling promiscious mode on eth0 does not help. I have to enable
it on the macvtap0 which is on top of eth0.
Stefan
3:47 a.m.
On 09.04.2015 10:39, Stefan Bauer wrote:
On Thu, 2015-04-09 at 10:12 +0200, Michal Privoznik wrote:
> I mildly recalls seeing a bug like this. The problem was in intel's
> kernel driver. A NIC by defaul checks incoming packets whether they
> match NIC's MAC. So if a TAP device was created over a NIC, it had to be
> put into promisc mode (automatically done by the driver) to allow
> different MACs and the check was done in kernel then. But since this
> generates too much interrupts, NICs HW was extended and it can be
> programmed with multiple MACs to let through. However, there was a bug
> which I recall of, that intel driver was not always putting the TAP MAC
> into the NIC HW correctly. Obviously, the bug was not visible if the NIC
> was put into promisc mode. And this may be what you are seeing. Let me
> see if I can find the bug.
FYI - enabling promiscious mode on eth0 does not help. I have to enable
it on the macvtap0 which is on top of eth0.
Ah, so that's not the bug then. Have you perhaps changed the vNIC MAC
inside the guest after it was started? Even though libvirt will nowadays
adapt to such change, older version of libvirt haven't this implemented
causing guest connectivity to break.
Michal
3:50 a.m.
On Thu, 2015-04-09 at 10:47 +0200, Michal Privoznik wrote:
Ah, so that's not the bug then. Have you perhaps changed the vNIC
MAC
inside the guest after it was started? Even though libvirt will nowadays
adapt to such change, older version of libvirt haven't this implemented
causing guest connectivity to break.
Nope. I only changed the nic mode from bridged to macvtap bridged mode
but always followed by a shutdown / start of the VM.
Anyway it's only an ipv6 problem - i do not have this problem with ipv4!
Stefan
4:03 a.m.
On 09.04.2015 10:50, Stefan Bauer wrote:
On Thu, 2015-04-09 at 10:47 +0200, Michal Privoznik wrote:
> Ah, so that's not the bug then. Have you perhaps changed the vNIC MAC
> inside the guest after it was started? Even though libvirt will nowadays
> adapt to such change, older version of libvirt haven't this implemented
> causing guest connectivity to break.
Nope. I only changed the nic mode from bridged to macvtap bridged mode
but always followed by a shutdown / start of the VM.
Anyway it's only an ipv6 problem - i do not have this problem with ipv4!
Maybe a firewall problem? Anything interesting in iptables/ebtables output?
Michal
4:01 a.m.
v4 is using arp to broadcast address (ff:ff:ff:ff:ff:ff) - that works
with macvtap without having card in promiscious mode (ip li is not
showing PROMISC flag).
v6 is using multicast to solicited node-address - that is NOT working
without enabling manually promiscious mode.
Stefan
11:52 a.m.
Further investigation shows that it is working as expected on linux
guests.
Only my win10 guests "trigger" that problem.
Will dig deeper...
Stefan
3:17 a.m.
I could narrow down the problem. Win7Prof and Windows 10 is having this
issue.
Win Client is member of the multicast group and is listening on
ff02::1:ffdf:fe88
Traffic from router -> client - captured on router:
07:41:23.104567 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
07:41:24.099764 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
07:41:25.099772 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
Traffic from router to client - captured on KVM HOST
09:41:23.106444 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
09:41:24.101647 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
09:41:25.101718 IP6 fe80::12fe:edff:fee6:cfa > ff02::1:ffdf:fe88: ICMP6,
neighbor solicitation, who has 2a01:198:200:8350:851e:21a7:28df:fe88,
length 32
No traffic seen on KVM GUEST (win7 or win10) with wireshark
Any ideas to debug this further?
Cheers
Stefan
3:40 a.m.
New subject: [libvirt] [SOLVED] Re: macvtap - no incoming ipv6 traffic processed on kvm host unless i start tcpdump on interface
It was the privacy extension enabled on the windows hosts.
So it was sending out from addresses the KVM HOST is not member of the
multicast group.
disabled it with netsh interface ipv6 set privacy state=disabled
Stefan
3560
days inactive
3567
days old
13 comments
3 participants
participants (3)
-
Martin Kletzander -
Michal Privoznik -
Stefan Bauer