[PATCH 37/67] docs: formatdomain: Remove 'elementsConsole' anchor
Some rewording and rewraping was needed to accomodate the new local
references.
Signed-off-by: Peter Krempa <pkrempa(a)redhat.com>
---
docs/formatdomain.rst | 27 +++++++++++++++------------
1 file changed, 15 insertions(+), 12 deletions(-)
diff --git a/docs/formatdomain.rst b/docs/formatdomain.rst
index b3d254520e..5f15c14093 100644
--- a/docs/formatdomain.rst
+++ b/docs/formatdomain.rst
@@ -4346,15 +4346,18 @@ after 0.9.5 (KVM only)` :
``redirdev``
The ``redirdev`` element is the main container for describing redirected
devices. ``bus`` must be "usb" for a USB device. An additional attribute
- ``type`` is required, matching one of the supported `serial
- device <#elementsConsole>`__ types, to describe the host side of the tunnel;
- ``type='tcp'`` or ``type='spicevmc'`` (which uses the usbredir channel
of a
- SPICE graphics device (See `Graphical framebuffers`_)) are typical. The redirdev
- element has an optional sub-element ``<address>`` which can tie the device to
- a particular controller. Further sub-elements, such as ``<source>``, may be
- required according to the given type, although a ``<target>`` sub-element is
- not required (since the consumer of the character device is the hypervisor
- itself, rather than a device visible in the guest).
+ ``type`` is required, matching one of the supported serial device types
+ (See `Consoles, serial, parallel & channel devices`_), to describe the host
+ side of the tunnel; ``type='tcp'`` or ``type='spicevmc'`` (which uses
the
+ usbredir channel of a SPICE graphics device (See `Graphical framebuffers`_))
+ are typical.
+
+ The redirdev element has an optional sub-element ``<address>`` which can tie
+ the device to a particular controller. Further sub-elements, such as
+ ``<source>``, may be required according to the given type, although a
+ ``<target>`` sub-element is not required (since the consumer of the
+ character device is the hypervisor itself, rather than a device visible in
+ the guest).
``boot``
Specifies that the device is bootable. The ``order`` attribute determines the
order in which devices will be tried during boot sequence. The per-device
@@ -4427,8 +4430,9 @@ behaves like a physical USB CCID (Chip/Smart Card Interface Device)
card.
possible to tunnel all requests through a secondary character device to a
third-party provider (which may in turn be talking to a smartcard or using
three certificate files). In this mode of operation, an additional attribute
- ``type`` is required, matching one of the supported `serial
- device <#elementsConsole>`__ types, to describe the host side of the tunnel;
+ ``type`` is required, matching one of the supported serial device types
+ (See `Consoles, serial, parallel & channel devices`_),
+ to describe the host side of the tunnel;
``type='tcp'`` or ``type='spicevmc'`` (which uses the smartcard
channel of a
SPICE graphics device (See `Graphical framebuffers`_)) are typical. Further
sub-elements, such as ``<source>``, may be required according to the given
@@ -6230,7 +6234,6 @@ A video device.
attribute which takes the value "io", "on" or "off".
At present, it's only
applicable to the bhyve's "gop" video model type ( :since:`Since
3.5.0` )
-:anchor:`<a id="elementsConsole"/>`
Consoles, serial, parallel & channel devices
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
--
2.35.3