Re: [libvirt] RFC: Migration with NPIV

Hi, This proposal is trying to figure out a solution for migration of domain which uses LUN behind vHBA as disk device (QEMU emulated disk only at this stage). And other related NPIV improvements which are not related with migration. I'm not luck to get a environment to test if the thoughts are workable, but I'd like see if guys have good idea/suggestions earlier. 1) Persistent vHBA support This is the useful stuff missed for long time. Assuming that one created a vHBA, did masking/zoning, everything works as expected. However, after a system rebooting, everything is just lost. If the user wants to get things back, he has to find out the preivous WWNN & WWPN, and create the vHBA again. On the other hand, Persistent vHBA support is actually required for domain which uses LUN behind a vHBA. Othewise the domain could fail to start after a system rebooting. To support the persistent vHBA, new APIs like virNodeDeviceDefineXML, virNodeDeviceUndefine is required. Also it's useful to introduce "autostart" for vHBA, so that the vHBA could be started automatically after system rebooting. Proposed APIs: virNodeDevicePtr virNodeDeviceDefineXML(virConnectPtr conn, const char *xml, unsigned int flags); int virNodeDeviceUndefine(virConnectPtr conn, virNodeDevicePtr dev, unsigned int flags); int virNodeDeviceSetAutostart(virNodeDevicePtr dev, int autostart, unsigned int flags); int virNodeDeviceGetAutostart(virNodeDevicePtr dev, int *autostart, unsigned int flags);

2) Associate vHBA with domain XML There are two ways to attach a LUN to a domain: as an QEMU emulated device; or passthrough. Since passthrough a LUN is not supported in libvirt yet, let's focus on the emulated LUN at this stage. New attributes "wwnn" and "wwpn" are introduced to indicate the LUN behind the vHBA. E.g. <disk type='block' device='disk'> <driver name='qemu' type='raw'/> <source wwnn="2001001b32a9da4e" wwpn="2101001b32a90004"/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </disk> Before the domain starting, we have to check if there is LUN assigned to the vHBA, error out if not. Using the stable path of LUN also works, e.g. <source dev="/dev/disk/by-path/pci-0000\:00\:07.0-scsi-0\:0\:0\:0"/> But the disadvantage is the user have to figure out the stable path himself; And we have to do checking of every stable path to see if it's behind a vHBA in migration "Begin" stage. Or an new XML tag for element "source" to indicate that it's behind a vHBA? such as: <source dev="disk-by-path" model="vport"/> 3) Migration with vHBA One possible solution for migration with vHBA is to use one pair of WWNN & WWPN on source host, one is using for domain, one is reserved for migration purpose. It requires the storage admin maps the same LUN to the two vHBAs when doing the masking and zoning. One of the two vHBA is called "Primary vHBA", another is called "secondary vHBA". To maitain the relationship between these two vHBAs, we have to introduce new XMLs to vHBA. E.g. In XML of primary vHBA: <secondary wwpn="2101001b32a90004"/> In XML of secondary vHBA: <primary wwpn="2101001b32a90002"/> Primary vHBA is going to be guaranteed not used by any domain which is driven by libvirt (we do some checking eariler before the domain starting). And it's also guaranteed that the LUN can't be used by other domain with sVirt or Sanlock. So it's safe to have two vHBAs on source host too. To prevent one using the LUN by creating vHBA using the same WWNN & WWPN on another host, we must create the secondary vHBA on source host, even it's not being used. Both primary and secondary vHBA must be defined and marked as "autostart" so that the domain could be started after system rebooting. When do migration, we have to bake a bigger cookie with secondary vHBA's info (basically it's WWNN and WWPN) in migration "Begin" stage, and eat that in migration "Prepare" stage on target host. In "Begin" stage, the XMLs represents the secondary vHBA is constructed. And the secondary vHBA is destoyed on source host, not undefined though. In "Prepare" stage, a new vHBA is created (define and start) on target host with the same WWNN & WWPN as secondary vHBA on source host. The LUN then should be visible to target host automatically? and thus migration can be performed. After migration is finished on target host, the primary vHBA on source host is destroyed, not undefined. If migration fails, the new vHBA created on target host will be destroyed and undefined. And both primary and secondary vHBA on source host will be started, so that the domain could be resumed. Finally if migration succeeds, primary vHBA on source host will be transtered to target host as secondary vHBA (defined). And both primary and secondary vHBA on source host will be undefined. 4) Enrich HBA's XML It's hard to known the vHBAs created from a HBA with current implementation. One have to dump XML of each (v)HBAs and find out the clue with element "parent" of vHBAs. It's good to introduce new element for HBA like "vports", so that one can easily known what (how many) vHBAs are created from the HBA? And also it's good to have the maximum vports the HBA supports. Except these, other useful information should be exposed too, such as the vendor name, the HBA state, PCI address, etc. The new XMLs should be like: <vports num='2' max='64'> <vport name="scsi_host40" wwpn="2101001b32a90004"/> <vport name="scsi_host40" wwpn="2101001b32a90005"/> </vports> <online/> <vendor>QLogic</vendor> <address type="pci" domain="0" bus="0" slot="5" function="0"/> "online", "vendor", "address" make sense to vHBA too. 5) Improve the way to lookup LUN's stable path Currently, to lookup the LUN's stable path with WWNN & WWPN, it needs to iterate over the sysfs each time, maintaining the stable path in vHBA's XML doesn't make sense, as the LUN assigned to the vHBA could be changed as the storage admin's mood. I'm wondering if there is a way to notify the change asynchronously, if there is, then maintaining the stable path internally make sense. 6) Miscellaneous This is only about QEMU emulated device, passthroughed scsi_host with vHBA is still not covered, we have to support the vHBA passthough first. The good thing is the solution should be similiar. Regards, Osier -- libvir-list mailing list libvir-list(a)redhat.com https://www.redhat.com/mailman/listinfo/libvir-list