4:14 a.m.
Hello,everyone:
I am trying to use libvirt API and libvirt-cim now. After installed them
successfully, I can see the "Virt_*****" providers using "cimprovider -l
-s"commond. My cimom is pegasus.
Then I used wbemcli as cim client. But when I used "wbemcli ei" to
enumerate instances of a specified class,for example,Xen_DiskPool, error code was:
wbemcli:Cim(1) CIM_ERR_FAILED: A general error occurred that is not covered by a more
specific error code:"For provider Virt_DevicePool the library name was empty. Check
provider registered location".
Could you please help me to solve this problem? Did it mean that the providers were
not registered correctly? But I "make postinstall" the provider and no errors
occourred.
Thank you!
Regards,
Chun Shan
Disclaimer:
The contents of this e-mail, and its attachments, if any, are confidential and may be
protected
by law against any unauthorized use. If you have received this e-mail by mistake or have
reason to believe that you are not the intended recipient, please notify the sender by
reply
e-mail as soon as possible and delete it from your computer system immediately
thereafter.
If you are not the intended recipient, you must not copy this e-mail or attachment or
disclose
the contents to any other person. While we have made every effort to keep our network
virus free,
we take no responsibility for any computer virus which might be transferred by way of this
e-mail.
6:04 p.m.
SC> wbemcli:Cim(1) CIM_ERR_FAILED: A general error occurred that
SC> is not covered by a more specific error code:"For provider
SC> Virt_DevicePool the library name was empty. Check provider
SC> registered location".
This usually happens because the CIMOM is unable to load some
dependent libraries for the providers.
Where did the .so files get installed? I think the default is
/usr/local/lib/cmpi for Pegasus if you don't specify a location.
Figure out where your Pegasus providers directory is and set that
with PROVIDERDIR like this:
./configure PROVIDERDIR=/usr/lib64/cmpi
Then clean and rebuild/reinstall your tree. Also, make sure that the
above path is set in your linker config (i.e. /etc/ld.so.conf).
--
Dan Smith
IBM Linux Technology Center
Open Hypervisor Team
email: danms(a)us.ibm.com
5:36 a.m.
New subject: 答复: Problems when using libvirt-cim provider
Hi， Mr. Smith:
Now the problem is solved. Thank you very much!
Best Regards
Chun Shan
Open System Software Laboratory
----------------------------------------------------------------------------
--
Hitachi (China) Research & Development Corporation
301, Tower C Raycom infotech Park, 2 kexueyuan Nanlu,
Hai Dian District, Beijing 100080, China
Tel:(86)-10-8286-2918 (Ext.) 371
Fax:(86)-10-8286-2919
E-mail: cshan(a)hitachi.cn
----------------------------------------------------------------------------
--
-----邮件原件-----
发件人: libvirt-cim-bounces(a)redhat.com
[mailto:libvirt-cim-bounces@redhat.com] 代表 Dan Smith
发送时间: 2008年7月29日 0:05
收件人: List for discussion and development of libvirt CIM
主题: Re: [Libvirt-cim] Problems when using libvirt-cim provider
SC> wbemcli:Cim(1) CIM_ERR_FAILED: A general error occurred that
SC> is not covered by a more specific error code:"For provider
SC> Virt_DevicePool the library name was empty. Check provider
SC> registered location".
This usually happens because the CIMOM is unable to load some
dependent libraries for the providers.
Where did the .so files get installed? I think the default is
/usr/local/lib/cmpi for Pegasus if you don't specify a location.
Figure out where your Pegasus providers directory is and set that
with PROVIDERDIR like this:
./configure PROVIDERDIR=/usr/lib64/cmpi
Then clean and rebuild/reinstall your tree. Also, make sure that the
above path is set in your linker config (i.e. /etc/ld.so.conf).
--
Dan Smith
IBM Linux Technology Center
Open Hypervisor Team
email: danms(a)us.ibm.com
5896
days inactive
5897
days old
2 comments
3 participants
participants (3)
-
cshan -
Dan Smith -
SHAN, CHUN -HCHBJ