[libvirt-users] stuck in pxe loop from uefi + tianocore/ovmf
Hello all, hope all is well Was wondering if I'm doing something wrong/missing something. I have pxe+tftp+uefi working between 2 vms. However after the build is done and I reboot, I still come up to pxe b/c tianocore always starts, from what I've seen, with trying PXE first. Great for initial builds :) but I would like to it stop after. In the xml I am pointing to the disk to boot first. if I virsh destory and run qemu directly on the qcow image, the vm comes up as expected and boots into the OS I have tried removing the nvram under /var/lib/libvirt/qemu/nvram/virtmachine. But the vm boots up and starts looking for pxe again. If I let that timeout, then type exit and select continue in the tianocore boot firmware, I just loop back into trying pxe over ipv4 etc I tried <rom bar='off'/> on the e1000 and that does work to stop pxe. Then I get to the uefi shell quickly, but all I see at that point is 2 BLK maps pointing to floppy 1 and 2. I see nothing when I try to manually add a new boot option. any help/wisdom would be appreciated. libvirtd (libvirt) 4.9.0 qemu command: sudo qemu-system-x86_64 -m 2048 -L /usr/share/ovmf/x64/ -bios OVMF_CODE.fd -drive file=/images/rdhcli02,format=qcow2,cache=writeback,if=virtio -device virtio-net,netdev=net10,mac=52:54:00:11:22:33 -netdev tap,id=net10,ifname=rdhcli02,script=no,downscript=no Is there a way to address this?
Any thoughts all? Just a final check-in. I have had help before and it is/was appreciated! Probably not explaining effectively or too corner case regards all On Fri, Jan 18, 2019 at 12:56 PM jsl6uy js16uy <js16uy@gmail.com> wrote:
Hello all, hope all is well Was wondering if I'm doing something wrong/missing something. I have pxe+tftp+uefi working between 2 vms. However after the build is done and I reboot, I still come up to pxe b/c tianocore always starts, from what I've seen, with trying PXE first. Great for initial builds :) but I would like to it stop after. In the xml I am pointing to the disk to boot first. if I virsh destory and run qemu directly on the qcow image, the vm comes up as expected and boots into the OS I have tried removing the nvram under /var/lib/libvirt/qemu/nvram/virtmachine. But the vm boots up and starts looking for pxe again. If I let that timeout, then type exit and select continue in the tianocore boot firmware, I just loop back into trying pxe over ipv4 etc I tried <rom bar='off'/> on the e1000 and that does work to stop pxe. Then I get to the uefi shell quickly, but all I see at that point is 2 BLK maps pointing to floppy 1 and 2. I see nothing when I try to manually add a new boot option.
any help/wisdom would be appreciated.
libvirtd (libvirt) 4.9.0
qemu command: sudo qemu-system-x86_64 -m 2048 -L /usr/share/ovmf/x64/ -bios OVMF_CODE.fd -drive file=/images/rdhcli02,format=qcow2,cache=writeback,if=virtio -device virtio-net,netdev=net10,mac=52:54:00:11:22:33 -netdev tap,id=net10,ifname=rdhcli02,script=no,downscript=no Is there a way to address this?
participants (1)
-
jsl6uy js16uy