11:56 p.m.
I have hit a problem running libvirt based containers in a CentOS 7
based host, with the extra wrinkle that my host is an EC2 instance in
AWS. Ultimately everything works as advertised, and I can launch
instances that host multiple libvirt lxc containers without problems,
with one caveat: About one time in ten when the containers are started,
the instance loses all network connectivity. This can even happen on
instances that host only a single container, so it's not related to the
number of containers that are being run. Once this happens, the only way
to fix the problem is to reboot the instance and hope that on the
reboot, the containers will start successfully this time.
In troubleshooting efforts that I've done I've found that the problem
does not occur with containers defined with the linuxcontainers.org
flavor of lxc. I've also discovered that if I configure my containers to
use libvirt's default isolated bridge device virbr0, this loss of
network connectivity does not appear to happen when the containers are
started. Specifically, I ran a test that repeatedly started/stopped a
single container configured with virbr0 and the test ran for a long time
without an issue. When I switched the container to use my fully
configured bridge device br0, the start/stop test usually hung up within
a few iterations. Meaning that my ssh session into the instance would
hang and I'd be unable to reconnect to the instance. Unfortunately AWS
does not provide an console back door into an instance so
troubleshooting has been difficult. I've checked the system logs though
after one of these hangs occurs and there are no errors reported
anywhere that I can see.
I do not see this problem when running on real hardware. I also do not
see the problem when running under other virtual environments, including
VMware, KVM, and VirtualBox. My guess is that it is a bug in libvirt
(since containers defined with the linuxcontainers.org lxc framework do
not cause this issue.) There seems to be an AWS component to the problem
as well though since I've only seen this happen in EC2 based instances.
Is anyone familiar with this problem? Does anyone have any suggestions
how I might resolve it? Note that I have tried a recent version of
libvirt (1.3.2-1) and it behaves the same as the stock CentOS version of
libvirt (1.2.17-13).
Peter
11:07 a.m.
If anyone is curious about this, the cause turned out to be related to
the way bridging works and how AWS deals with arp table updates. The
underlying problem is described here:
http://backreference.org/2010/07/28/linux-bridge-mac-addresses-and-dynami...
The solution was to add the line
MACADDR=<mac-addr>
to the ifcfg-br0 file used to define the bridge interface the containers
reference. The mac address should be set to the mac address of the
interface hosting the bridge (e.g. eth0). By adding this line, the
bridge uses the same mac address as its host interface and it never
changes. Without this entry, the bridge's mac address changes whenever a
container is started to match that of the container just started. This
can cause a flood of arps and that was causing issues for the AWS
networking infrastructure.
Peter
On 06/03/2016 09:56 PM, Peter Steele wrote:
I have hit a problem running libvirt based containers in a CentOS 7
based host, with the extra wrinkle that my host is an EC2 instance in
AWS. Ultimately everything works as advertised, and I can launch
instances that host multiple libvirt lxc containers without problems,
with one caveat: About one time in ten when the containers are
started, the instance loses all network connectivity. This can even
happen on instances that host only a single container, so it's not
related to the number of containers that are being run. Once this
happens, the only way to fix the problem is to reboot the instance and
hope that on the reboot, the containers will start successfully this
time.
In troubleshooting efforts that I've done I've found that the problem
does not occur with containers defined with the linuxcontainers.org
flavor of lxc. I've also discovered that if I configure my containers
to use libvirt's default isolated bridge device virbr0, this loss of
network connectivity does not appear to happen when the containers are
started. Specifically, I ran a test that repeatedly started/stopped a
single container configured with virbr0 and the test ran for a long
time without an issue. When I switched the container to use my fully
configured bridge device br0, the start/stop test usually hung up
within a few iterations. Meaning that my ssh session into the instance
would hang and I'd be unable to reconnect to the instance.
Unfortunately AWS does not provide an console back door into an
instance so troubleshooting has been difficult. I've checked the
system logs though after one of these hangs occurs and there are no
errors reported anywhere that I can see.
I do not see this problem when running on real hardware. I also do not
see the problem when running under other virtual environments,
including VMware, KVM, and VirtualBox. My guess is that it is a bug in
libvirt (since containers defined with the linuxcontainers.org lxc
framework do not cause this issue.) There seems to be an AWS component
to the problem as well though since I've only seen this happen in EC2
based instances.
Is anyone familiar with this problem? Does anyone have any suggestions
how I might resolve it? Note that I have tried a recent version of
libvirt (1.3.2-1) and it behaves the same as the stock CentOS version
of libvirt (1.2.17-13).
Peter
3252
days inactive
3262
days old
1 comments
1 participants
participants (1)
-
Peter Steele