2:51 p.m.
I finally figured out my VNC configuration, so I can now run virt-manager to inspect and
manipulate my VM.
I initially created the VM with "virt-install", but I haven't been able to
see the console or do anything with it.
When I ran virt-manager, I tried to configure the vcpus (1->4) and change the boot
order (cdrom, then disk, as I created the VM with an ISO).
When I made these changes, virt-manager said they would take effect on the next restart of
the VM. So, then I tried to restart the VM from virt-manager. The "Run" button
is disabled, so I assume that means it detects that the VM is running. I've tried
clicking "Shut Down" and selecting "Reboot" from the dropdown, but
neither of those seem to do anything. I've tried to view the console window, but
I've only ever seen a black screen there.
I believe some people mentioned that I should try sshing to the VM. I would do that if I
could find an IP address or hostname that appears to correspond to this VM. The obvious,
using the VM name, didn't work.
I'm not sure what to do here.
2:43 a.m.
In virt-manager, the 'open' button opens the screen of your guest. If your screen
is blank, press a button to wake-up your screen. If still nothing appears, maybe your
guest doesn't boot correctly??
To use the shutdown function, acpi needs to be enabled. On some OS's this isn't
the standard setting and you will have to enable it yourself. But if your guest
doesn't boot correctly, the acpi deamon (or equivalent) isn't started yet...
You can look for the ip with tools like tcpdump... But again, if your guest doesn't
boot correctly, chances are that the network of your guest isn't up yet...
Dominique.
-----Oorspronkelijk bericht-----
Van: libvirt-users-bounces(a)redhat.com [mailto:libvirt-users-bounces@redhat.com] Namens
KARR, DAVID
Verzonden: maandag 13 juli 2015 21:51
Aan: libvirt-users(a)redhat.com
Onderwerp: [libvirt-users] Can't figure out how to restart VM after making config
changes in virt-manager
I finally figured out my VNC configuration, so I can now run virt-manager to inspect and
manipulate my VM.
I initially created the VM with "virt-install", but I haven't been able to
see the console or do anything with it.
When I ran virt-manager, I tried to configure the vcpus (1->4) and change the boot
order (cdrom, then disk, as I created the VM with an ISO).
When I made these changes, virt-manager said they would take effect on the next restart of
the VM. So, then I tried to restart the VM from virt-manager. The "Run" button
is disabled, so I assume that means it detects that the VM is running. I've tried
clicking "Shut Down" and selecting "Reboot" from the dropdown, but
neither of those seem to do anything. I've tried to view the console window, but
I've only ever seen a black screen there.
I believe some people mentioned that I should try sshing to the VM. I would do that if I
could find an IP address or hostname that appears to correspond to this VM. The obvious,
using the VM name, didn't work.
I'm not sure what to do here.
_______________________________________________
libvirt-users mailing list
libvirt-users(a)redhat.com
https://www.redhat.com/mailman/listinfo/libvirt-users
8:23 a.m.
On 13.07.2015 21:51, KARR, DAVID wrote:
I finally figured out my VNC configuration, so I can now run
virt-manager to inspect and manipulate my VM.
I initially created the VM with "virt-install", but I haven't been able to
see the console or do anything with it.
When I ran virt-manager, I tried to configure the vcpus (1->4) and change the boot
order (cdrom, then disk, as I created the VM with an ISO).
When I made these changes, virt-manager said they would take effect on the next restart
of the VM. So, then I tried to restart the VM from virt-manager. The "Run"
button is disabled, so I assume that means it detects that the VM is running. I've
tried clicking "Shut Down" and selecting "Reboot" from the dropdown,
but neither of those seem to do anything. I've tried to view the console window, but
I've only ever seen a black screen there.
I believe some people mentioned that I should try sshing to the VM. I would do that if I
could find an IP address or hostname that appears to correspond to this VM. The obvious,
using the VM name, didn't work.
I'm not sure what to do here.
Yeah, sometimes it's not clear when we are referring to a reboot of
guest OS or reboot of whole VM (= process where libvirt is involved so
the changes can finally take effect, e.g. in qemu world new process with
brand new command line is spawned). If unsure it's safe to assume the
latter.
Now, shutting down a domain can be difficult. Esp. if you want to do
that nicely. Imagine that your VM is a real piece of HW, but with blank
screen as you say. What possibilities do you have? You can try pressing
the power button (implemented as 'virsh shutdown --mode acpi $dom'), or
have a process running within the system initiate the shutdown process
('virsh shutdown --mode agent $dom'). Both cases meet some assumptions,
e.g. the system does not ignore ACPI events, or has the process (guest
agent as we call it) running.
There's of course the obvious option - pull the plug (equivalent to
'virsh destroy $dom') but you risk data loss.
SSH-ing into the host could do the trick too. And libvirt even has an
API for that: virDomainInterfaceAddresses() exposed in virsh under
domifaddr command. That may tell you the IP address(-es) assigned to a
guest. But not in all cases. Yet.
Michal
3454
days inactive
3456
days old
2 comments
3 participants
participants (3)
-
Dominique Ramaekers -
KARR, DAVID -
Michal Privoznik