Re: [libvirt] [PATCH] qemu: call drive_unplug in DetachPciDiskDevice

On Thu, Oct 21, 2010 at 11:53:29AM -0500, Ryan Harper wrote: > * Daniel P. Berrange <berrange(a)redhat.com&gt; [2010-10-21 11:46]: > > On Thu, Oct 21, 2010 at 08:50:35AM -0500, Ryan Harper wrote: > > > Currently libvirt doesn't confirm whether the guest has responded to the > > > disk removal request. In some cases this can leave the guest with > > > continued access to the device while the mgmt layer believes that it has > > > been removed. With a recent qemu monitor command[1] we can > > > deterministically revoke a guests access to the disk (on the QEMU side) > > > to ensure no futher access is permitted. > > > > > > This patch adds support for the drive_unplug() command and introduces it > > > in the disk removal paths. There is some discussion to be had about how > > > to handle the case where the guest is running in a QEMU without this > > > command (and the fact that we currently don't have a way of detecting > > > what monitor commands are available). > > > > Basically we try to run the command and then catch the failure. > > > > For QMP, we can check for a error with a class of 'CommandNotFound', > > > > For HMP, QEMU will print 'unknown command' in the reply. > > > > Neither is ideal, since neither is a guarenteed part of the monitor > > interface, but it is all we have to go on, and ensure other critical > > errors will still be treated as fatal by libvirt. > > Yeah, this sorta already works without explictly catching the error > (unless you want to display a different message at caller level than > command not found). This would cause the hot-unplug operation to completely terminate though, whereas we want it to carry on, if the command is not present. If we get a command-not-found, then we should syslog a warning, and then return '0' (ie success) to the caller of qemuMonitorDriveUnplug Alternatively, return '+1' to the caller, and make the callers check for '+1', syslog it and treat it as non-fatal. This is closer to the approach we use for handling 'balloon device not present' error when code runs the 'info balloon' method. > > > My current implementation assumes that if you don't have a QEMU with > > > this capability that we should fail the device removal. This is a > > > strong statement around hotplug that isn't consistent with previous > > > releases so I'm open to other approachs, but given the potential data > > > leakage problem hot-remove can lead to without drive_unplug, I think > > > it's the right thing to do. > > > > I don't think we can do this, since it obviously breaks every single > > existing deployment out there. Users who have sVirt enabled will > > have a level of protection from the data leakage, so I don't think > > it is a severe problem. > > Yeah, I was thinking we could re-work the logic to only completely fail > in the case where the command wasn't found/successful *and* we don't > have sVirt enabled. I'm still wary of doing that because of the significant negative impact on existing deployments out there, even in the case where hotunplug would complete just fine. I think we'll just need to syslog the potential issue and people can upgrade their QMEU if they need the extra security

Regards, Daniel -- |: Red Hat, Engineering, London -o- http://people.redhat.com/berrange/ :| |: http://libvirt.org -o- http://virt-manager.org -o- http://deltacloud.org :| |: http://autobuild.org -o- http://search.cpan.org/~danberr/ :| |: GnuPG: 7D3B9505 -o- F3C9 553F A1DA 4AC2 5648 23C1 B3DF F742 7D3B 9505 :|