To clean up the VF I use
ip link set dev p4p2 vf 0 mac 0 and it working
24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovs-system state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:b1, vlan 190, spoof checking off, link-state enable
vf 3 MAC aa:bb:cc:00:00:12, vlan 190, spoof checking off, link-state enable
[root@r-ufm160 devstack]# ip link set dev enp3s0f0 vf 3 mac 0
[root@r-ufm160 devstack]# ip link show enp3s0f0
24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovs-system state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:b1, vlan 190, spoof checking off, link-state enable
vf 3 MAC 00:00:00:00:00:b1, vlan 190, spoof checking off, link-state enable
It just put the address 00:00:00:00:00:b1 which I don’t know why, but as I remember the same behavior is in intel cards (I think is related to iproute)
I used fedora 2.1 with kernel 4.1.13-100.
The most annoying part is that in OpenStack if I use an SR-IOV VF (interface hostdev) for VM and delete it I can’t reuse it for macvtap (interface direct) so I have to
clean the mac
by running ip link set dev p4p2 vf 0 mac 0
I guess I will need to workaround it in OpenStack.
From: sendmail [mailto:justsendmailnothingelse@gmail.com]
On Behalf Of Laine Stump
Sent: Tuesday, December 15, 2015 9:45 PM
To: Libvirt <libvir-list@redhat.com>
Cc: Moshe Levi <moshele@mellanox.com>; vyasevic@redhat.com
Subject: Re: [libvirt] <interface type='hostdev'>vf configuration cleanup when VM is delete
On 12/15/2015 01:34 PM, Laine Stump wrote:
On 12/13/2015 10:51 AM, Moshe Levi wrote:
Hi,
I have a setup with libvirt 1.3.0 and OpenStack trunk.
Before launched the VM ip link command show the following VF mac/vlan configuration [1]
When I launch a VM with <interface type='hostdev'> via openstack api (OpenStack direct port)
I can see that the VF get the mac/vlan according to libvrit xml [2] and ip link command [3], but when I delete the VM the mac/vlan config are still shown as in [3] and not restored to [1]
Shouldn’t libvirt restore the mac/vlan to [1].
The same problem exists when using <interface type='direct'> (OpenStack macvtap port) but just for the MAC configuration of the VF.
What libvirt does is to restore the MAC address to whatever it was before we set it up for use with a guest. Although there are some sriov net drivers that (for some unfathomable reason) think it's cool to assign a random MAC address to each VF at boot time,
the "normal" thing is for the VFs to have a MAC address of all 0's to start with. So libvirt should be saving 00:00:00:00:00:00 (it will be in the file /var/run/libvirt/hostdevmgr/$ifname_vf$vfnum) then setting the MAC to use; when done, libvirt will read
the 00:00:00:00:00:00 and use netlink to set the MAC address, but this is apparently failing.
I checked on my Fedora 22 system with the igb driver, and found that if the MAC address was originally set to something other than 0's, it was restored properly by libvirt, but if it was set to all 0's originally, the attempt to set it back to 0 would fail.
I then tried doing the same thing with the "ip" utility:
# ip link set dev p4p2 vf 0 mac 00:00:00:00:00:00
and I get the following response:
RTNETLINK answers: Invalid argument
So it appears that either the kernel or the NIC driver is refusing to set the MAC address to all 0's. I'm reasonably certain this is a regression in the kernel,
Sigh. It appears that this has "always" been the case - I just checked on a 2.6.32-573 RHEL kernel, and a 3.10.x RHEL7.2 kernel, and 4.1 (Fedora 22) and both of them also refuse to set the MAC address to 00:00:00:00:00:00. I'm not sure if this limitation is
in the NIC driver or some basic code in the kernel.
although I can't say how long it's been there, as I don't normally pay attention to this (and as I said, many SRIOV NIC drivers don't default their VFs to 0 MAC addresses)
What distro and kernel are you using for your tests?
[1] - 24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovs-system state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 3 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
[2] - <interface type='hostdev' managed='yes'>
<mac address=' fa:16:3e:11:af:fe '/>
<driver name='kvm'/>
<source>
<address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x7'/>
</source>
<vlan>
<tag id='190'/>
</vlan>
<alias name='hostdev0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</interface>
[3] 24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovs-system state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 3 MAC fa:16:3e:11:af:fe, vlan 190, spoof checking off, link-state enable
--
libvir-list mailing list
libvir-list@redhat.com
https://www.redhat.com/mailman/listinfo/libvir-list
F15
--
libvir-list mailing list
libvir-list@redhat.com
https://www.redhat.com/mailman/listinfo/libvir-list