[PATCH] systemd: start libvirtd after firewalld/iptables services
When a system has enabled the iptables/ip6tables services rather than
firewalld, there is no explicit ordering of the start of those
services vs. libvirtd. This creates a problem when libvirtd.service is
started before ip[6]tables, as the latter, when it finally is started,
will remove all of the iptables rules that had previously been added
by libvirt, including the custom chains where libvirt's rules are
kept. This results in an error message similar to the following when a
user subsequently tries to start a new libvirt network:
"Error while activating network: Call to virNetworkCreate failed:
internal error: Failed to apply firewall rules
/usr/sbin/ip6tables -w --table filter --insert LIBVIRT_FWO \
--in-interface virbr2 --jump REJECT:
ip6tables: No chain/target/match by that name."
(Prior to logging this error, it also would have caused failure to
forward (or block) traffic in some cases, e.g. for guests on a NATed
network, since libvirt's rules to forward/block had all been deleted
and libvirt didn't know about it, so it couldn't fix the problem)
When this happens, the problem can be remedied by simply restarting
libvirtd.service (which has the side-effect of reloading all
libvirt-generated firewall rules)
Instead, we can just explicitly stating in the libvirtd.service file
that libvirtd.service should start after ip6tables.service and
ip6tables.service, eliminating the race condition that leads to the
error.
There is also nothing (that I can see) in the systemd .service files
to guarantee that firewalld.service will be started (if enabled) prior
to libvirtd.service. The same error scenario given above would occur
if libvirtd.service started before firewalld.service. Even before
that, though libvirtd would have detected that firewalld.service was
disabled, and then turn off all firewalld support. So, for example,
firewalld's libvirt zone wouldn't be used, and most likely traffic
from guests would therefore be blocked (all with no external
indication of the source of the problem other than a debug-level log
when libvirtd was started saying that firewalld wasn't in use); also
libvirtd wouldn't notice when firewalld reloaded its rules (which also
simultaneously deletes all of libvirt's rules).
I'm not aware of any reports that have been traced back to
libvirtd.service starting before firewalld.service, but have seen that
error reported multiple times, and also don't see an existing
dependency that would guarantee firewalld.service starts before
libvirtd.service, so it's possible it's been happening and we just
haven't gotten to the bottom of it.
This patch adds an After= line to the libvirtd.service file for each
of iptables.service, ip6tables.service, and firewalld.servicee, which
should guarantee that libvirtd.service isn't started until systemd has
started whichever of the others is enabled.
This race was diagnosed, and patch proposed, by Jason Montleon in
https://bugzilla.redhat.com/1723698 . At the time (April 2019) danpb
agreed with him that this change to libvirtd.service was a reasonable
thing to do, but I guess everyone thought someone else was going to
post a patch, so in the end nobody did.
Signed-off-by: Laine Stump <laine(a)redhat.com>
---
src/remote/libvirtd.service.in | 3 +++
1 file changed, 3 insertions(+)
diff --git a/src/remote/libvirtd.service.in b/src/remote/libvirtd.service.in
index 90b2cad5b0..cc0d4e3693 100644
--- a/src/remote/libvirtd.service.in
+++ b/src/remote/libvirtd.service.in
@@ -11,6 +11,9 @@ Wants=libvirtd-admin.socket
Wants=systemd-machined.service
Before=libvirt-guests.service
After=network.target
+After=firewalld.service
+After=iptables.service
+After=ip6tables.service
After=dbus.service
After=iscsid.service
After=apparmor.service
--
2.25.4